Practice Exams:

Network Appliance NS0-165 Dumps

EXAM: NetApp Certified Data Administrator, ONTAP
Verified By Experts
Premium Bundle
$49.99

NS0-165 Premium ETE File


  • Premium File 60 Questions & Answers
Whats Included:
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

Network Appliance NS0-165 Practice Test 60

Question 590

A storage support case shows the correct LUN created but mapped to an old test-server igroup rather than the production host. Which action and validation evidence belong together?

  1. Action: Configure a supported FC target and switch zoning design that permits intended initiators to see the appropriate ONTAP target ports. Validation: Inspect approved WWPN zones and confirm the host sees target ports and expected multipath devices after discovery.
  2. Action: Create ONTAP initiator groups with the correct host IQNs or WWPNs and map LUNs only to intended hosts. Validation: Check a test LUN map from the intended initiator while confirming an unrelated initiator cannot see it.
  3. Action: Choose supported ONTAP NVMe namespace and subsystem access only after confirming the target ONTAP release, transport and host initiator support. Validation: Test one authorized NVMe namespace discovery and device I/O using a compatible host and documented fabric.
  4. Action: Enable supported iSCSI service on an SVM, provide reachable iSCSI data LIFs and map the correct LUN to authorized initiators. Validation: From a sanctioned test initiator, log in to approved targets and verify only the intended LUN identifier is discovered.

Explanation

Correct Answer

B:

The situation is that a storage support case shows the correct LUN created but mapped to an old test-server igroup rather than the production host. Create ONTAP initiator groups with the correct host IQNs or WWPNs and map LUNs only to intended hosts. Validation: Check a test LUN map from the intended initiator while confirming an unrelated initiator cannot see it. The action and test belong together because an igroup is an access-control association for block initiators and must reflect the supported host identity and operating system context.

Incorrect Answers

A:

The situation is that a storage support case shows the correct LUN created but mapped to an old test-server igroup rather than the production host. “plan fibre channel zoning and ONTAP target wwpn access” evaluates a different intervention. The appropriate action is to create ONTAP initiator groups with the correct host IQNs or WWPNs and map LUNs only to intended hosts. To confirm, check a test LUN map from the intended initiator while confirming an unrelated initiator cannot see it.

C:

The situation is that a storage support case shows the correct LUN created but mapped to an old test-server igroup rather than the production host. That action-and-evidence pair concerns “validate nvme over fabrics namespace and host compatibility”, not this decision. The appropriate action is to create ONTAP initiator groups with the correct host IQNs or WWPNs and map LUNs only to intended hosts. To confirm, check a test LUN map from the intended initiator while confirming an unrelated initiator cannot see it.

D:

The proposed pair focuses on “configure iscsi target access with supported svm interfaces and initiators” instead. The appropriate action is to create ONTAP initiator groups with the correct host IQNs or WWPNs and map LUNs only to intended hosts. To confirm, check a test LUN map from the intended initiator while confirming an unrelated initiator cannot see it.

Question 591

During an enterprise ONTAP operations review, A Windows or Linux host sees four FC paths to an ONTAP LUN and needs correct path selection and failover behavior. What is the most appropriate next decision?

  1. Create ONTAP initiator groups with the correct host IQNs or WWPNs and map LUNs only to intended hosts.
  2. Choose supported ONTAP NVMe namespace and subsystem access only after confirming the target ONTAP release, transport and host initiator support.
  3. Install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior.
  4. Enable supported iSCSI service on an SVM, provide reachable iSCSI data LIFs and map the correct LUN to authorized initiators.

Explanation

Correct Answer

C:

Install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration. To verify, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

Incorrect Answers

A:

This alternative focuses on “use igroups and lun mapping for explicit host access” instead of the required outcome. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

B:

That choice concerns “validate nvme over fabrics namespace and host compatibility”, not the immediate requirement. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

D:

“configure iscsi target access with supported svm interfaces and initiators” is related to another task, not the failure shown here. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Question 592

A Windows or Linux host sees four FC paths to an ONTAP LUN and needs correct path selection and failover behavior. Why does the recommended approach address this particular concern?

  1. NVMe/TCP or NVMe/FC access uses namespace/subsystem concepts and host tooling that differ from classic SCSI LUN mapping.
  2. An igroup is an access-control association for block initiators and must reflect the supported host identity and operating system context.
  3. Creating a LUN is only part of SAN service provisioning; target discovery and LUN masking determine which hosts can access it.
  4. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Explanation

Correct Answer

D:

Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration. This supports the decision to install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior.

Incorrect Answers

A:

“validate nvme over fabrics namespace and host compatibility” explains a different mechanism. Here, multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

B:

That statement concerns “use igroups and lun mapping for explicit host access” rather than the cause in this case. Here, multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

C:

The principle behind “configure iscsi target access with supported svm interfaces and initiators” is not the one being tested. Here, multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Question 593

A Windows or Linux host sees four FC paths to an ONTAP LUN and needs correct path selection and failover behavior. Which evidence best validates the proposed outcome?

  1. Run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.
  2. From a sanctioned test initiator, log in to approved targets and verify only the intended LUN identifier is discovered.
  3. Record host path transitions and ONTAP target health, then run a supported single-path fault test after correction.
  4. Test one authorized NVMe namespace discovery and device I/O using a compatible host and documented fabric.

Explanation

Correct Answer

A:

Run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path. It is the relevant test because multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Incorrect Answers

B:

This evidence addresses “configure iscsi target access with supported svm interfaces and initiators” instead of confirming the repair. To check this result, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

C:

“investigate mpio path thrashing before changing storage capacity” would verify a different part of the system. To check this result, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

D:

That test concerns “validate nvme over fabrics namespace and host compatibility”, not the requested outcome. To check this result, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

Question 594

Consider this situation: A Windows or Linux host sees four FC paths to an ONTAP LUN and needs correct path selection and failover behavior. A team member suggests: "Attach a critical LUN over one unprotected SAN connection and call it highly available because the storage has two controllers." What is the main risk?

  1. Concurrent block writes can corrupt the filesystem or expose sensitive application storage.
  2. A single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes.
  3. Unauthorized file access may become possible without fixing the underlying authentication failure.
  4. Hosts can be exposed to unintended targets and difficult-to-debug path conflicts or security risks.

Explanation

Correct Answer

B:

A single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes. The shortcut is unsafe because multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Incorrect Answers

A:

The alternative risk relates to “Concurrent block writes can corrupt the filesystem or expose sensitive application storage”, not the stated mistake. Here, a single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes.

C:

That consequence concerns “Unauthorized file access may become possible without fixing the underlying authentication failure”, which is a different failure. Here, a single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes.

D:

“Hosts can be exposed to unintended targets and difficult-to-debug path conflicts or security risks” does not describe the result of this shortcut. Here, a single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes.

Question 595

A storage operations lead considers: A Windows or Linux host sees four FC paths to an ONTAP LUN and needs correct path selection and failover behavior. Which response and evidence should be linked?

  1. Action: Configure a supported FC target and switch zoning design that permits intended initiators to see the appropriate ONTAP target ports. Validation: Inspect approved WWPN zones and confirm the host sees target ports and expected multipath devices after discovery.
  2. Action: Create ONTAP initiator groups with the correct host IQNs or WWPNs and map LUNs only to intended hosts. Validation: Check a test LUN map from the intended initiator while confirming an unrelated initiator cannot see it.
  3. Action: Install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. Validation: Run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.
  4. Action: Organize SVM NAS access with suitable junctions, qtrees, quotas and export or share policies matched to departmental ownership. Validation: Verify a test share points to the intended junction and that a configured qtree quota and ACL enforce the policy.

Explanation

Correct Answer

C:

Install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. Validation: Run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path. The action and test belong together because multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Incorrect Answers

A:

The linked action and check for “plan fibre channel zoning and ONTAP target wwpn access” would not resolve this case. The appropriate action is to install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. To confirm, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

B:

That action-and-evidence pair concerns “use igroups and lun mapping for explicit host access”, not this decision. The appropriate action is to install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. To confirm, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

D:

“use nas qtrees and namespace structure for manageable datasets” evaluates a different intervention. The appropriate action is to install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. To confirm, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

Question 596

An enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. Which action best addresses this requirement?

  1. Configure a supported FC target and switch zoning design that permits intended initiators to see the appropriate ONTAP target ports.
  2. Review client mount path, source volume junctions and namespace changes when Linux applications encounter stale file handle errors.
  3. Enable supported iSCSI service on an SVM, provide reachable iSCSI data LIFs and map the correct LUN to authorized initiators.
  4. Install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior.

Explanation

Correct Answer

D:

The situation is that an enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. Install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration. To verify, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

Incorrect Answers

A:

That choice concerns “plan fibre channel zoning and ONTAP target wwpn access”, not the immediate requirement. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

B:

The proposed action addresses “investigate nfs stale file handles after namespace modifications” rather than the problem described. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

C:

The situation is that an enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. “configure iscsi target access with supported svm interfaces and initiators” is related to another task, not the failure shown here. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Question 597

A NetApp storage engineer considers: An enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. Which underlying principle applies?

  1. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.
  2. An igroup is an access-control association for block initiators and must reflect the supported host identity and operating system context.
  3. Creating a LUN is only part of SAN service provisioning; target discovery and LUN masking determine which hosts can access it.
  4. An accessible NFS server can reject a mount because the client's subnet or authentication does not match the configured policy.

Explanation

Correct Answer

A:

The situation is that an enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration. This supports the decision to install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior.

Incorrect Answers

B:

The principle behind “use igroups and lun mapping for explicit host access” is not the one being tested. Here, multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

C:

“configure iscsi target access with supported svm interfaces and initiators” describes another technical distinction. Here, multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

D:

“troubleshoot nfs access denied through export policy and permissions” explains a different mechanism. Here, multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Question 598

An enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. What should the team examine before accepting the result?

  1. From a sanctioned test initiator, log in to approved targets and verify only the intended LUN identifier is discovered.
  2. Run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.
  3. Upload and read a synthetic object through the intended API and test the application's required update behavior before rollout.
  4. Inspect approved WWPN zones and confirm the host sees target ports and expected multipath devices after discovery.

Explanation

Correct Answer

B:

The situation is that an enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. Run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path. It is the relevant test because multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Incorrect Answers

A:

The situation is that an enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. This evidence addresses “configure iscsi target access with supported svm interfaces and initiators” instead of confirming the repair. To check this result, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

C:

That test concerns “clarify s3 object operations versus ONTAP nas file semantics”, not the requested outcome. To check this result, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

D:

The proposed check is relevant to “plan fibre channel zoning and ONTAP target wwpn access”, but not sufficient here. To check this result, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

Question 599

An enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. The proposed shortcut is: "Attach a critical LUN over one unprotected SAN connection and call it highly available because the storage has two controllers." Which failure is most likely?

  1. The action may overwrite recoverable data while an application-level filesystem issue persists.
  2. Hosts can be exposed to unintended targets and difficult-to-debug path conflicts or security risks.
  3. A single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes.
  4. The application may see no disk or an unauthorized initiator could be allowed through careless mapping.

Explanation

Correct Answer

C:

The situation is that an enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. A single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes. The shortcut is unsafe because multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Incorrect Answers

A:

“The action may overwrite recoverable data while an application-level filesystem issue persists” can arise elsewhere, but it is not the most direct risk here. Here, a single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes.

B:

That consequence concerns “Hosts can be exposed to unintended targets and difficult-to-debug path conflicts or security risks”, which is a different failure. Here, a single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes.

D:

The alternative risk relates to “The application may see no disk or an unauthorized initiator could be allowed through careless mapping”, not the stated mistake. Here, a single switch or adapter fault may disconnect the host from block storage despite healthy ONTAP nodes.

Question 600

For this case—An enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration.—which implementation and acceptance check are correctly paired?

  1. Action: Create ONTAP initiator groups with the correct host IQNs or WWPNs and map LUNs only to intended hosts. Validation: Check a test LUN map from the intended initiator while confirming an unrelated initiator cannot see it.
  2. Action: Enable supported iSCSI service on an SVM, provide reachable iSCSI data LIFs and map the correct LUN to authorized initiators. Validation: From a sanctioned test initiator, log in to approved targets and verify only the intended LUN identifier is discovered.
  3. Action: Choose supported ONTAP NVMe namespace and subsystem access only after confirming the target ONTAP release, transport and host initiator support. Validation: Test one authorized NVMe namespace discovery and device I/O using a compatible host and documented fabric.
  4. Action: Install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. Validation: Run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

Explanation

Correct Answer

D:

The situation is that an enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. Install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. Validation: Run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path. The action and test belong together because multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Incorrect Answers

A:

The situation is that an enterprise SAN redesign adds redundant switches but the servers have no validated multipath configuration. That action-and-evidence pair concerns “use igroups and lun mapping for explicit host access”, not this decision. The appropriate action is to install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. To confirm, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

B:

The proposed pair focuses on “configure iscsi target access with supported svm interfaces and initiators” instead. The appropriate action is to install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. To confirm, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

C:

“validate nvme over fabrics namespace and host compatibility” evaluates a different intervention. The appropriate action is to install and configure supported host multipath software and ONTAP target paths according to ALUA or applicable asymmetric access behavior. To confirm, run a controlled failure of one SAN fabric path and verify the host keeps its LUN available through a supported alternate path.

NetApp Certified Data Administrator, ONTAP (NS0-165) Practice Tests