Practice Exams:

Network Appliance NS0-165 Dumps

EXAM: NetApp Certified Data Administrator, ONTAP
Verified By Experts
Premium Bundle
$49.99

NS0-165 Premium ETE File


  • Premium File 60 Questions & Answers
Whats Included:
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

Network Appliance NS0-165 Practice Test 63

Question 620

A SAN support engineer finds the expected FC target online but the server's WWPN is absent from its igroup. Which action and validation evidence belong together?

  1. Action: Separate host OS filesystem diagnostics from LUN connectivity and storage hardware health before choosing corrective action. Validation: Check SAN device consistency and host filesystem diagnostic output on an isolated test volume, then follow an approved recovery workflow.
  2. Action: Review HBA state, zoning, WWPN registration, target port health and host rescans before troubleshooting LUN filesystem contents. Validation: Check fabric name server discovery, allowed zones and ONTAP FC target port state during a test rescan.
  3. Action: Compare host multipath path states, ALUA priorities and switch errors when SAN I/O switches between paths unexpectedly. Validation: Record host path transitions and ONTAP target health, then run a supported single-path fault test after correction.
  4. Action: Verify LUN state, initiator group membership, mapping and host rescan before changing unrelated storage network settings. Validation: Inspect a test igroup and LUN mapping alongside the host device list before and after a documented rescan.

Explanation

Correct Answer

D:

The situation is that a SAN support engineer finds the expected FC target online but the server's WWPN is absent from its igroup. Verify LUN state, initiator group membership, mapping and host rescan before changing unrelated storage network settings. Validation: Inspect a test igroup and LUN mapping alongside the host device list before and after a documented rescan. The action and test belong together because a host can log in to SAN targets successfully yet discover no mapped storage because authorization is incomplete.

Incorrect Answers

A:

That action-and-evidence pair concerns “distinguish host filesystem corruption from san transport faults”, not this decision. The appropriate action is to verify LUN state, initiator group membership, mapping and host rescan before changing unrelated storage network settings. To confirm, inspect a test igroup and LUN mapping alongside the host device list before and after a documented rescan.

B:

The proposed pair focuses on “diagnose fc path visibility using fabric and switch evidence” instead. The appropriate action is to verify LUN state, initiator group membership, mapping and host rescan before changing unrelated storage network settings. To confirm, inspect a test igroup and LUN mapping alongside the host device list before and after a documented rescan.

C:

“investigate mpio path thrashing before changing storage capacity” evaluates a different intervention. The appropriate action is to verify LUN state, initiator group membership, mapping and host rescan before changing unrelated storage network settings. To confirm, inspect a test igroup and LUN mapping alongside the host device list before and after a documented rescan.

Question 621

For this ONTAP storage administration case, A Linux initiator can ping its ONTAP iSCSI LIF but cannot complete CHAP authentication. What is the most appropriate next decision?

  1. Check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence.
  2. Separate host OS filesystem diagnostics from LUN connectivity and storage hardware health before choosing corrective action.
  3. Compare host multipath path states, ALUA priorities and switch errors when SAN I/O switches between paths unexpectedly.
  4. Review HBA state, zoning, WWPN registration, target port health and host rescans before troubleshooting LUN filesystem contents.

Explanation

Correct Answer

A:

Check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup. To verify, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

Incorrect Answers

B:

“distinguish host filesystem corruption from san transport faults” is related to another task, not the failure shown here. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

C:

This alternative focuses on “investigate mpio path thrashing before changing storage capacity” instead of the required outcome. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

D:

That choice concerns “diagnose fc path visibility using fabric and switch evidence”, not the immediate requirement. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Question 622

A Linux initiator can ping its ONTAP iSCSI LIF but cannot complete CHAP authentication. Why does the recommended approach address this particular concern?

  1. A missing FC target can be a fabric registration or zoning problem upstream of LUN presentation.
  2. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.
  3. Path selection instability can produce latency without any shortage of aggregate space or backend disk performance.
  4. A writable LUN may be online while its guest filesystem has errors; restoring transport cannot repair corrupted filesystem metadata.

Explanation

Correct Answer

B:

Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup. This supports the decision to check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence.

Incorrect Answers

A:

The principle behind “diagnose fc path visibility using fabric and switch evidence” is not the one being tested. Here, network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

C:

“investigate mpio path thrashing before changing storage capacity” explains a different mechanism. Here, network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

D:

That statement concerns “distinguish host filesystem corruption from san transport faults” rather than the cause in this case. Here, network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Question 623

A Linux initiator can ping its ONTAP iSCSI LIF but cannot complete CHAP authentication. Which evidence best validates the proposed outcome?

  1. Inspect a test igroup and LUN mapping alongside the host device list before and after a documented rescan.
  2. Check SAN device consistency and host filesystem diagnostic output on an isolated test volume, then follow an approved recovery workflow.
  3. Use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.
  4. Record host path transitions and ONTAP target health, then run a supported single-path fault test after correction.

Explanation

Correct Answer

C:

Use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order. It is the relevant test because network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Incorrect Answers

A:

“diagnose san lun missing from igroup or map” would verify a different part of the system. To check this result, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

B:

That test concerns “distinguish host filesystem corruption from san transport faults”, not the requested outcome. To check this result, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

D:

This evidence addresses “investigate mpio path thrashing before changing storage capacity” instead of confirming the repair. To check this result, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

Question 624

Consider this situation: A Linux initiator can ping its ONTAP iSCSI LIF but cannot complete CHAP authentication. A team member suggests: "Disable CHAP and allow all initiators after a typo in one client's target portal address prevents discovery." What is the main risk?

  1. The host continues experiencing I/O stalls while a larger disk allocation wastes resources.
  2. The host remains without its disk while a disruptive cluster change fails to address the actual mapping issue.
  3. The action may overwrite recoverable data while an application-level filesystem issue persists.
  4. Storage remains unavailable and the security posture is unnecessarily weakened.

Explanation

Correct Answer

D:

Storage remains unavailable and the security posture is unnecessarily weakened. The shortcut is unsafe because network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Incorrect Answers

A:

That consequence concerns “The host continues experiencing I/O stalls while a larger disk allocation wastes resources”, which is a different failure. Here, storage remains unavailable and the security posture is unnecessarily weakened.

B:

“The host remains without its disk while a disruptive cluster change fails to address the actual…” does not describe the result of this shortcut. Here, storage remains unavailable and the security posture is unnecessarily weakened.

C:

The alternative risk relates to “The action may overwrite recoverable data while an application-level filesystem issue persists”, not the stated mistake. Here, storage remains unavailable and the security posture is unnecessarily weakened.

Question 625

A storage operations lead considers: A Linux initiator can ping its ONTAP iSCSI LIF but cannot complete CHAP authentication. Which response and evidence should be linked?

  1. Action: Check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. Validation: Use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.
  2. Action: Compare host multipath path states, ALUA priorities and switch errors when SAN I/O switches between paths unexpectedly. Validation: Record host path transitions and ONTAP target health, then run a supported single-path fault test after correction.
  3. Action: Review HBA state, zoning, WWPN registration, target port health and host rescans before troubleshooting LUN filesystem contents. Validation: Check fabric name server discovery, allowed zones and ONTAP FC target port state during a test rescan.
  4. Action: Separate host OS filesystem diagnostics from LUN connectivity and storage hardware health before choosing corrective action. Validation: Check SAN device consistency and host filesystem diagnostic output on an isolated test volume, then follow an approved recovery workflow.

Explanation

Correct Answer

A:

Check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. Validation: Use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order. The action and test belong together because network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Incorrect Answers

B:

“investigate mpio path thrashing before changing storage capacity” evaluates a different intervention. The appropriate action is to check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. To confirm, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

C:

The linked action and check for “diagnose fc path visibility using fabric and switch evidence” would not resolve this case. The appropriate action is to check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. To confirm, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

D:

That action-and-evidence pair concerns “distinguish host filesystem corruption from san transport faults”, not this decision. The appropriate action is to check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. To confirm, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

Question 626

A new server uses an outdated target portal IP and reports no discovered iSCSI targets. Which action best addresses this requirement?

  1. Separate host OS filesystem diagnostics from LUN connectivity and storage hardware health before choosing corrective action.
  2. Check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence.
  3. Verify LUN state, initiator group membership, mapping and host rescan before changing unrelated storage network settings.
  4. Review HBA state, zoning, WWPN registration, target port health and host rescans before troubleshooting LUN filesystem contents.

Explanation

Correct Answer

B:

The situation is that a new server uses an outdated target portal IP and reports no discovered iSCSI targets. Check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup. To verify, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

Incorrect Answers

A:

The situation is that a new server uses an outdated target portal IP and reports no discovered iSCSI targets. “distinguish host filesystem corruption from san transport faults” is related to another task, not the failure shown here. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

C:

That choice concerns “diagnose san lun missing from igroup or map”, not the immediate requirement. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

D:

The proposed action addresses “diagnose fc path visibility using fabric and switch evidence” rather than the problem described. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Question 627

A NetApp storage engineer considers: A new server uses an outdated target portal IP and reports no discovered iSCSI targets. Which underlying principle applies?

  1. A writable LUN may be online while its guest filesystem has errors; restoring transport cannot repair corrupted filesystem metadata.
  2. A host can log in to SAN targets successfully yet discover no mapped storage because authorization is incomplete.
  3. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.
  4. Multiple discovered target ports do not assure the host will use optimal paths or survive path failure without proper multipath integration.

Explanation

Correct Answer

C:

The situation is that a new server uses an outdated target portal IP and reports no discovered iSCSI targets. Network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup. This supports the decision to check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence.

Incorrect Answers

A:

“distinguish host filesystem corruption from san transport faults” describes another technical distinction. Here, network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

B:

“diagnose san lun missing from igroup or map” explains a different mechanism. Here, network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

D:

The principle behind “design alua and host multipathing for resilient san access” is not the one being tested. Here, network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Question 628

A new server uses an outdated target portal IP and reports no discovered iSCSI targets. What should the team examine before accepting the result?

  1. Check fabric name server discovery, allowed zones and ONTAP FC target port state during a test rescan.
  2. Check SAN device consistency and host filesystem diagnostic output on an isolated test volume, then follow an approved recovery workflow.
  3. Record host path transitions and ONTAP target health, then run a supported single-path fault test after correction.
  4. Use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

Explanation

Correct Answer

D:

The situation is that a new server uses an outdated target portal IP and reports no discovered iSCSI targets. Use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order. It is the relevant test because network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Incorrect Answers

A:

That test concerns “diagnose fc path visibility using fabric and switch evidence”, not the requested outcome. To check this result, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

B:

The proposed check is relevant to “distinguish host filesystem corruption from san transport faults”, but not sufficient here. To check this result, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

C:

The situation is that a new server uses an outdated target portal IP and reports no discovered iSCSI targets. This evidence addresses “investigate mpio path thrashing before changing storage capacity” instead of confirming the repair. To check this result, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

Question 629

A new server uses an outdated target portal IP and reports no discovered iSCSI targets. The proposed shortcut is: "Disable CHAP and allow all initiators after a typo in one client's target portal address prevents discovery." Which failure is most likely?

  1. Storage remains unavailable and the security posture is unnecessarily weakened.
  2. The underlying client discovery issue remains while application data may be destroyed.
  3. The host remains without its disk while a disruptive cluster change fails to address the actual mapping issue.
  4. The original endpoint issue may persist while object traffic becomes vulnerable to interception.

Explanation

Correct Answer

A:

The situation is that a new server uses an outdated target portal IP and reports no discovered iSCSI targets. Storage remains unavailable and the security posture is unnecessarily weakened. The shortcut is unsafe because network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Incorrect Answers

B:

The alternative risk relates to “The underlying client discovery issue remains while application data may be destroyed”, not the stated mistake. Here, storage remains unavailable and the security posture is unnecessarily weakened.

C:

“The host remains without its disk while a disruptive cluster change fails to address the actual…” can arise elsewhere, but it is not the most direct risk here. Here, storage remains unavailable and the security posture is unnecessarily weakened.

D:

That consequence concerns “The original endpoint issue may persist while object traffic becomes vulnerable to interception”, which is a different failure. Here, storage remains unavailable and the security posture is unnecessarily weakened.

Question 630

For this case—A new server uses an outdated target portal IP and reports no discovered iSCSI targets.—which implementation and acceptance check are correctly paired?

  1. Action: Review HBA state, zoning, WWPN registration, target port health and host rescans before troubleshooting LUN filesystem contents. Validation: Check fabric name server discovery, allowed zones and ONTAP FC target port state during a test rescan.
  2. Action: Check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. Validation: Use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.
  3. Action: Verify LUN state, initiator group membership, mapping and host rescan before changing unrelated storage network settings. Validation: Inspect a test igroup and LUN mapping alongside the host device list before and after a documented rescan.
  4. Action: Separate host OS filesystem diagnostics from LUN connectivity and storage hardware health before choosing corrective action. Validation: Check SAN device consistency and host filesystem diagnostic output on an isolated test volume, then follow an approved recovery workflow.

Explanation

Correct Answer

B:

The situation is that a new server uses an outdated target portal IP and reports no discovered iSCSI targets. Check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. Validation: Use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order. The action and test belong together because network reachability, target discovery, session authentication and block mapping are separate stages of iSCSI setup.

Incorrect Answers

A:

“diagnose fc path visibility using fabric and switch evidence” evaluates a different intervention. The appropriate action is to check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. To confirm, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

C:

That action-and-evidence pair concerns “diagnose san lun missing from igroup or map”, not this decision. The appropriate action is to check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. To confirm, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

D:

The proposed pair focuses on “distinguish host filesystem corruption from san transport faults” instead. The appropriate action is to check target portal routing, initiator IQN, iSCSI service state and CHAP settings in a controlled sequence. To confirm, use a test initiator to confirm TCP reachability, discovery, authenticated login and mapped LUN visibility in order.

NetApp Certified Data Administrator, ONTAP (NS0-165) Practice Tests