Practice Exams:

HP HPE7-A01 Dumps

EXAM: HPE Network Campus Access Professional
Verified By Experts
Premium Bundle
$19.99
$54.99 $74.98

HPE7-A01 Premium Bundle


  • Premium File 204 Questions & Answers
  • Study Guide 1264 Pages

HP HPE7-A01 Practice Test 27

Question 260

At a regional hospital network, the network team reports that a new user VLAN has no local DHCP server and clients never receive offers from the central server. Select TWO complementary choices: the targeted response and an acceptance test that verifies it.

  1. Configure the correct DHCP relay destination on the VLAN gateway interface
  2. Capture Discover and relayed DHCP packets on both sides
  3. Inspect broadcast rates, discard counters and physical link topology
  4. Align MC-LAG identifiers and the supported VSX peer configuration
  5. Configure and validate the intended LLDP-MED voice network policy and access VLANs

Explanation

Correct Answers

A:

The selected action is Configure the correct DHCP relay destination on the VLAN gateway interface. Its matching outcome check is to capture Discover and relayed DHCP packets on both sides.

B:

The selected action is Capture Discover and relayed DHCP packets on both sides. Its matching outcome check is to capture Discover and relayed DHCP packets on both sides.

Incorrect Answers

C:

The proposed alternative—inspect broadcast rates, discard counters and physical link topology—does not address the current failure. Instead, configure the correct DHCP relay destination on the VLAN gateway interface.

D:

The proposed alternative—align MC-LAG identifiers and the supported VSX peer configuration—does not address the current failure. Instead, configure the correct DHCP relay destination on the VLAN gateway interface.

E:

The proposed alternative—configure and validate the intended LLDP-MED voice network policy and access VLANs—does not address the current failure. Instead, configure the correct DHCP relay destination on the VLAN gateway interface.

Question 261

At an industrial manufacturing site, the network engineering team reports that switch interface counters show increasing CRC errors whenever a fiber uplink carries peak load. Which configuration or operating decision most directly addresses the issue?

  1. Configure the correct DHCP relay destination on the VLAN gateway interface
  2. Verify consistent supported MTU along every forwarding link and VLAN interface in the path
  3. Mark only authorized DHCP uplinks as trusted and enable DHCP snooping where supported
  4. Inspect optics, light levels and cabling before retuning routing protocols

Explanation

Correct Answer

D:

Inspect optics, light levels and cabling before retuning routing protocols. CRC errors indicate link-level corruption that may be caused by physical conditions. Confirm the result using this test: Correlate CRC increments with optic diagnostics and corrected media.

Incorrect Answers

A:

The proposed alternative—configure the correct DHCP relay destination on the VLAN gateway interface—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

B:

The proposed alternative—verify consistent supported MTU along every forwarding link and VLAN interface in the path—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

C:

The proposed alternative—mark only authorized DHCP uplinks as trusted and enable DHCP snooping where supported—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

Question 262

At an industrial manufacturing site, the network engineering team reports that switch interface counters show increasing CRC errors whenever a fiber uplink carries peak load. A design review identifies an unsupported shortcut. Which assumption should the team reject for this particular problem?

  1. Change BGP local preference and assume the physical errors stop
  2. Assume tagging all other VLANs also corrects the native VLAN mismatch
  3. Increase the root bridge priority to hide the unauthorized bridge
  4. Add a static default route on clients that have not yet received addresses

Explanation

Correct Answer

A:

The shortcut at issue is to change BGP local preference and assume the physical errors stop. The corrective choice is: Inspect optics, light levels and cabling before retuning routing protocols.

Incorrect Answers

B:

The shortcut to assume tagging all other VLANs also corrects the native VLAN mismatch is not the error in this case. The actual risk comes from change BGP local preference and assume the physical errors stop.

C:

The shortcut to increase the root bridge priority to hide the unauthorized bridge is not the error in this case. The actual risk comes from change BGP local preference and assume the physical errors stop.

D:

The shortcut to add a static default route on clients that have not yet received addresses is not the error in this case. The actual risk comes from change BGP local preference and assume the physical errors stop.

Question 263

At an industrial manufacturing site, the network engineering team reports that switch interface counters show increasing CRC errors whenever a fiber uplink carries peak load. Which technical reasoning most specifically justifies the recommended solution?

  1. An edge-port BPDU can indicate an unexpected bridge that threatens topology stability
  2. CRC errors indicate link-level corruption that may be caused by physical conditions
  3. ARP inspection can reject inconsistent IP-to-MAC claims on untrusted interfaces
  4. Port mirroring provides a copy of observed frames for packet analysis

Explanation

Correct Answer

B:

CRC errors indicate link-level corruption that may be caused by physical conditions. This is the technical reason behind the proposed approach: “Inspect optics, light levels and cabling before retuning routing protocols”. The result should be checked by “Correlate CRC increments with optic diagnostics and corrected media”.

Incorrect Answers

A:

The proposed alternative—an edge-port BPDU can indicate an unexpected bridge that threatens topology stability—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

C:

The proposed alternative—aRP inspection can reject inconsistent IP-to-MAC claims on untrusted interfaces—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

D:

The proposed alternative—port mirroring provides a copy of observed frames for packet analysis—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

Question 264

At an industrial manufacturing site, the network engineering team reports that switch interface counters show increasing CRC errors whenever a fiber uplink carries peak load. Which test would most directly show that the requested outcome was achieved?

  1. Submit a mismatched ARP mapping and inspect drop counters
  2. Measure per-member counters across several separate flows
  3. Inject a test rogue RA and verify client default-gateway selection
  4. Correlate CRC increments with optic diagnostics and corrected media

Explanation

Correct Answer

D:

The outcome check is to correlate CRC increments with optic diagnostics and corrected media. It measures whether the stated requirement was met.

Incorrect Answers

A:

The proposed alternative—submit a mismatched ARP mapping and inspect drop counters—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

B:

The proposed alternative—measure per-member counters across several separate flows—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

C:

The proposed alternative—inject a test rogue RA and verify client default-gateway selection—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

Question 265

At an industrial manufacturing site, the network engineering team reports that switch interface counters show increasing CRC errors whenever a fiber uplink carries peak load. Select TWO complementary choices: the targeted response and an acceptance test that verifies it.

  1. Inspect MAC move logs and port topology before and after correction
  2. Verify LACP mode, member speed and matching aggregation configuration
  3. Apply IPv6 router-advertisement guard on untrusted access ports where supported
  4. Correlate CRC increments with optic diagnostics and corrected media
  5. Inspect optics, light levels and cabling before retuning routing protocols

Explanation

Correct Answers

D:

The selected action is Correlate CRC increments with optic diagnostics and corrected media.

E:

The selected action is Inspect optics, light levels and cabling before retuning routing protocols.

Incorrect Answers

A:

The proposed alternative—inspect MAC move logs and port topology before and after correction—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

B:

The proposed alternative—verify LACP mode, member speed and matching aggregation configuration—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

C:

The proposed alternative—apply IPv6 router-advertisement guard on untrusted access ports where supported—does not address the current failure. Instead, inspect optics, light levels and cabling before retuning routing protocols.

Question 266

At a university engineering campus, the engineering team reports that network operations cannot see the packets entering an AP uplink for an approved diagnostic capture. Which configuration or operating decision most directly addresses the issue?

  1. Inspect optics, light levels and cabling before retuning routing protocols
  2. Apply BPDU protection to designated edge ports and recover only after the loop source is addressed
  3. Configure a bounded mirror source and monitor destination for the affected interface
  4. Verify consistent supported MTU along every forwarding link and VLAN interface in the path

Explanation

Correct Answer

C:

Configure a bounded mirror source and monitor destination for the affected interface. Port mirroring provides a copy of observed frames for packet analysis. Confirm the result using this test: Validate the capture contains the expected source MAC and VLAN tags.

Incorrect Answers

A:

The proposed alternative—inspect optics, light levels and cabling before retuning routing protocols—does not address this requirement. Port mirroring provides a copy of observed frames for packet analysis.

B:

The proposed alternative—apply BPDU protection to designated edge ports and recover only after the loop source is addressed—does not address this requirement. Port mirroring provides a copy of observed frames for packet analysis.

D:

The proposed alternative—verify consistent supported MTU along every forwarding link and VLAN interface in the path—does not address this requirement. Port mirroring provides a copy of observed frames for packet analysis.

Question 267

At a university engineering campus, the engineering team reports that network operations cannot see the packets entering an AP uplink for an approved diagnostic capture. A design review identifies an unsupported shortcut. Which assumption should the team reject for this particular problem?

  1. Mirror an unrelated trunk and claim it represents the affected AP interface
  2. Configure only additional access VLAN IDs and assume routing follows automatically
  3. Trust every classroom access port to prevent clients from losing DHCP
  4. Increase the root bridge priority to hide the unauthorized bridge

Explanation

Correct Answer

A:

The shortcut at issue is to mirror an unrelated trunk and claim it represents the affected AP interface. Port mirroring provides a copy of observed frames for packet analysis. The corrective choice is: Configure a bounded mirror source and monitor destination for the affected interface.

Incorrect Answers

B:

The shortcut to configure only additional access VLAN IDs and assume routing follows automatically is not the error in this case. The actual risk comes from mirror an unrelated trunk and claim it represents the affected AP interface.

C:

The shortcut to trust every classroom access port to prevent clients from losing DHCP is not the error in this case. The actual risk comes from mirror an unrelated trunk and claim it represents the affected AP interface.

D:

The shortcut to increase the root bridge priority to hide the unauthorized bridge is not the error in this case. The actual risk comes from mirror an unrelated trunk and claim it represents the affected AP interface.

Question 268

At a university engineering campus, the engineering team reports that network operations cannot see the packets entering an AP uplink for an approved diagnostic capture. Which technical reasoning most specifically justifies the recommended solution?

  1. Snooping restricts multicast forwarding according to learned receiver memberships
  2. Port mirroring provides a copy of observed frames for packet analysis
  3. Relay forwards client broadcasts across routed network boundaries to the server
  4. SVIs supply the Layer-3 boundary between separate Layer-2 VLANs

Explanation

Correct Answer

B:

Port mirroring provides a copy of observed frames for packet analysis. This is the technical reason behind the proposed approach: “Configure a bounded mirror source and monitor destination for the affected interface”. The result should be checked by “Validate the capture contains the expected source MAC and VLAN tags”.

Incorrect Answers

A:

The proposed alternative—snooping restricts multicast forwarding according to learned receiver memberships—does not address this requirement. Port mirroring provides a copy of observed frames for packet analysis.

C:

The proposed alternative—relay forwards client broadcasts across routed network boundaries to the server—does not address this requirement. Port mirroring provides a copy of observed frames for packet analysis.

D:

The proposed alternative—sVIs supply the Layer-3 boundary between separate Layer-2 VLANs—does not address this requirement. Port mirroring provides a copy of observed frames for packet analysis.

Question 269

At a university engineering campus, the engineering team reports that network operations cannot see the packets entering an AP uplink for an approved diagnostic capture. Which test would most directly show that the requested outcome was achieved?

  1. Inject a test rogue RA and verify client default-gateway selection
  2. Test permitted and blocked traffic while inspecting rule hit counts
  3. Capture Discover and relayed DHCP packets on both sides
  4. Validate the capture contains the expected source MAC and VLAN tags

Explanation

Correct Answer

D:

The outcome check is to validate the capture contains the expected source MAC and VLAN tags. It measures whether the stated requirement was met. Port mirroring provides a copy of observed frames for packet analysis.

Incorrect Answers

A:

The suggested check—inject a test rogue RA and verify client default-gateway selection—does not test the required result. Instead, validate the capture contains the expected source MAC and VLAN tags.

B:

The suggested check—test permitted and blocked traffic while inspecting rule hit counts—does not test the required result. Instead, validate the capture contains the expected source MAC and VLAN tags.

C:

The suggested check—capture Discover and relayed DHCP packets on both sides—does not test the required result. Instead, validate the capture contains the expected source MAC and VLAN tags.

Question 270

At a university engineering campus, the engineering team reports that network operations cannot see the packets entering an AP uplink for an approved diagnostic capture. Select TWO complementary choices: the targeted response and an acceptance test that verifies it.

  1. Permit the required VLAN on both ends of the tagged uplink without exposing unrelated VLANs
  2. Configure a bounded mirror source and monitor destination for the affected interface
  3. Fail a redundant link and record port roles and reconvergence time
  4. Validate the capture contains the expected source MAC and VLAN tags
  5. Apply IPv6 router-advertisement guard on untrusted access ports where supported

Explanation

Correct Answers

B:

The selected action is Configure a bounded mirror source and monitor destination for the affected interface. Its matching outcome check is to validate the capture contains the expected source MAC and VLAN tags.

D:

The selected action is Validate the capture contains the expected source MAC and VLAN tags. Its matching outcome check is to validate the capture contains the expected source MAC and VLAN tags.

Incorrect Answers

A:

The proposed alternative—permit the required VLAN on both ends of the tagged uplink without exposing unrelated VLANs—does not address this requirement. Port mirroring provides a copy of observed frames for packet analysis.

C:

The proposed alternative—fail a redundant link and record port roles and reconvergence time—does not address this requirement. Port mirroring provides a copy of observed frames for packet analysis.

E:

The proposed alternative—apply IPv6 router-advertisement guard on untrusted access ports where supported—does not address this requirement. Port mirroring provides a copy of observed frames for packet analysis.

HPE Network Campus Access Professional (HPE7-A01) Practice Tests