Practice Exams:

Fortinet NSE4_FGT_AD-7.6 Dumps

EXAM: Fortinet NSE 4 - FortiOS 7.6 Administrator
Verified By Experts
Premium Bundle
$49.99

NSE4_FGT_AD-7.6 Premium ETE File


  • Premium File 94 Questions & Answers
Whats Included:
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

Fortinet NSE4_FGT_AD-7.6 Practice Test 61

Question 600

At a managed branch perimeter, a FortiGate running FortiOS 7.6 has this observation: Long-lived application sessions do not instantly move to a recovered preferred uplink even though new sessions do. The operator corrected the configuration by choosing to differentiate existing-session pinning from new-session path selection when testing SD-WAN changes. Select TWO answers that together provide a falsifiable acceptance test and a preventive change gate.

  1. Disconnect the primary test link and verify connectivity through the backup route.
  2. Check the route table and selected SD-WAN member for a routed session.
  3. Trace the destination and confirm ARP or neighbor resolution on the intended egress.
  4. Create fresh and persistent sessions and compare their selected SD-WAN members.
  5. Require peer review for sd-wan session persistence changes and an acceptance check that will create fresh and persistent sessions and compare their selected SD-WAN members before relevant releases.

Explanation

Correct Answers

D:

It measures the operational result after the correction to differentiate existing-session pinning from new-session path selection when testing SD-WAN changes, and it directly checks the reported condition: long-lived application sessions do not instantly move to a recovered preferred uplink even though new sessions do. For sd-wan session persistence, a saved profile or healthy dashboard alone would not verify that the affected flow behaves as required.

E:

The organization already encountered the failure where long-lived application sessions do not instantly move to a recovered preferred uplink even though new sessions do, so every relevant future change should be reviewed for the same hazard. Combined with the separate acceptance test to create fresh and persistent sessions and compare their selected SD-WAN members, this gate checks future revisions without claiming that the current configuration is permanently correct.

Incorrect Answers

A:

The proposed evidence, to disconnect the primary test link and verify connectivity through the backup route, checks backup route continuity in a situation such as a branch should switch to its LTE uplink if the primary static WAN path is unavailable, not the required sd-wan session persistence acceptance. For the affected firewall behavior the directly discriminating check is to create fresh and persistent sessions and compare their selected SD-WAN members, alongside a review of sd-wan session persistence rather than backup route continuity settings.

B:

The proposed evidence, to check the route table and selected SD-WAN member for a routed session, checks sd-wan static-route prerequisite in a situation such as an SD-WAN rule exists but traffic never enters the SD-WAN zone because routing lacks an eligible path, not the required sd-wan session persistence acceptance. For the affected firewall behavior the directly discriminating check is to create fresh and persistent sessions and compare their selected SD-WAN members, alongside a review of sd-wan session persistence rather than sd-wan static-route prerequisite settings.

C:

The proposed evidence, to trace the destination and confirm ARP or neighbor resolution on the intended egress, checks static route egress interface in a situation such as a new static route points to a WAN interface different from the network that reaches its next-hop gateway, not the required sd-wan session persistence acceptance. For the affected firewall behavior the directly discriminating check is to create fresh and persistent sessions and compare their selected SD-WAN members, alongside a review of sd-wan session persistence rather than static route egress interface settings.

Question 601

A FortiOS 7.6 review of a datacenter security boundary reports the following condition: Two provider paths seem healthy but one set of applications consistently uses an unexpected member. The requirement concerns sd-wan path diagnostics while retaining existing unrelated controls. Which FortiGate change MOST directly meets the requirement?

  1. Correct next-hop reachability and interface selection rather than focusing only on route syntax.
  2. Inspect SD-WAN health check status and service-rule decision output for representative flows.
  3. Configure a properly scoped blackhole route to prevent fallback for that protected destination.
  4. Set performance SLA targets for loss, latency, and jitter and steer the voice service to a healthy link.

Explanation

Correct Answer

B:

Choosing to inspect SD-WAN health check status and service-rule decision output for representative flows changes the component implicated by that observation, rather than masking the symptom through a different firewall feature. Operators can substantiate the choice by carrying out this test: compare health status, service match, and selected member for an affected flow.

Incorrect Answers

A:

Selecting correct next-hop reachability and interface selection rather than focusing only on route syntax would focus the new configuration on unreachable static gateway, for which a static route exists in configuration but traffic cannot reach its specified next-hop gateway may be a valid concern, but this sd-wan path diagnostics configuration has a different failure. Evidence for sd-wan path diagnostics requires staff to compare health status, service match, and selected member for an affected flow; the proposed unreachable static gateway change cannot deliver that sd-wan path diagnostics result by itself.

C:

Configuring a properly scoped blackhole route to prevent fallback for that protected destination would focus the new configuration on blackhole route protection, for which an intentionally disallowed destination prefix is leaking over a catch-all WAN route when its specific tunnel is absent may be a valid concern, but this sd-wan path diagnostics configuration has a different failure. Evidence for sd-wan path diagnostics requires staff to compare health status, service match, and selected member for an affected flow; the proposed blackhole route protection change cannot deliver that sd-wan path diagnostics result by itself.

D:

Setting performance SLA targets for loss, latency, and jitter and steer the voice service to a healthy link would focus the new configuration on performance sla packet loss, for which voice calls degrade on a high-loss WAN link while another member meets the application SLA may be a valid concern, but this sd-wan path diagnostics configuration has a different failure. Evidence for sd-wan path diagnostics requires staff to compare health status, service match, and selected member for an affected flow; the proposed performance sla packet loss change cannot deliver that sd-wan path diagnostics result by itself.

Question 602

During FortiOS 7.6 operations at an enterprise gateway change window, the evidence is: Two provider paths seem healthy but one set of applications consistently uses an unexpected member. Basic reachability and unrelated systems have already been checked. Which configuration mistake BEST explains this sd-wan path diagnostics failure?

  1. Specify a gateway address unreachable from the chosen egress network.
  2. Depend on the default internet route to handle sensitive private tunnel destinations.
  3. Diagnose the wrong egress member from physical interface link lights alone.
  4. Choose the lowest nominal interface cost without considering packet-loss SLA failure.

Explanation

Correct Answer

C:

The problem arises when administrators diagnose the wrong egress member from physical interface link lights alone, so the failing behavior has a concrete configuration cause and is not inferred from an unrelated metric. The relevant repair is to inspect SD-WAN health check status and service-rule decision output for representative flows.

Incorrect Answers

A:

The alternative cause involving unreachable static gateway can produce a different failure, for example when a static route exists in configuration but traffic cannot reach its specified next-hop gateway; it is not the sd-wan path diagnostics case. The more specific error here is the choice to diagnose the wrong egress member from physical interface link lights alone; check it by attempting to compare health status, service match, and selected member for an affected flow before making an unrelated unreachable static gateway change.

B:

The alternative cause involving blackhole route protection can produce a different failure, for example when an intentionally disallowed destination prefix is leaking over a catch-all WAN route when its specific tunnel is absent; it is not the sd-wan path diagnostics case. The more specific error here is the choice to diagnose the wrong egress member from physical interface link lights alone; check it by attempting to compare health status, service match, and selected member for an affected flow before making an unrelated blackhole route protection change.

D:

The alternative cause involving performance sla packet loss can produce a different failure, for example when voice calls degrade on a high-loss WAN link while another member meets the application SLA; it is not the sd-wan path diagnostics case. The more specific error here is the choice to diagnose the wrong egress member from physical interface link lights alone; check it by attempting to compare health status, service match, and selected member for an affected flow before making an unrelated performance sla packet loss change.

Question 603

At a redundant regional firewall pair, a FortiGate running FortiOS 7.6 has this observation: Two provider paths seem healthy but one set of applications consistently uses an unexpected member. Investigators confirmed this cause: administrators chose to diagnose the wrong egress member from physical interface link lights alone. Which action MOST directly corrects the confirmed error?

  1. Inspect SD-WAN health check status and service-rule decision output for representative flows.
  2. Set performance SLA targets for loss, latency, and jitter and steer the voice service to a healthy link.
  3. Configure a properly scoped blackhole route to prevent fallback for that protected destination.
  4. Diagnose the wrong egress member from physical interface link lights alone.

Explanation

Correct Answer

A:

This addresses sd-wan path diagnostics without needlessly weakening separate security or routing controls. Given the observed condition—two provider paths seem healthy but one set of applications consistently uses an unexpected member—the operator should then compare health status, service match, and selected member for an affected flow.

Incorrect Answers

B:

Changing the mechanism to set performance SLA targets for loss, latency, and jitter and steer the voice service to a healthy link could be a sensible correction for performance sla packet loss when voice calls degrade on a high-loss WAN link while another member meets the application SLA. The targeted fix is to inspect SD-WAN health check status and service-rule decision output for representative flows; a review of performance sla packet loss would not, by itself, prove that the team can compare health status, service match, and selected member for an affected flow.

C:

Changing the mechanism to configure a properly scoped blackhole route to prevent fallback for that protected destination could be a sensible correction for blackhole route protection when an intentionally disallowed destination prefix is leaking over a catch-all WAN route when its specific tunnel is absent. The targeted fix is to inspect SD-WAN health check status and service-rule decision output for representative flows; a review of blackhole route protection would not, by itself, prove that the team can compare health status, service match, and selected member for an affected flow.

D:

The proposal repeats the confirmed sd-wan path diagnostics error by choosing to diagnose the wrong egress member from physical interface link lights alone. A corrective change must instead inspect SD-WAN health check status and service-rule decision output for representative flows and then produce the measurable result to compare health status, service match, and selected member for an affected flow; repeating the failed setting cannot serve as a repair.

Question 604

A FortiOS 7.6 review of a remote-office migration reports the following condition: Two provider paths seem healthy but one set of applications consistently uses an unexpected member. The incident has been fixed, and the owner wants to prevent a recurrence of the sd-wan path diagnostics problem. Which future change-control rule is MOST appropriate?

  1. Require peer review for unreachable static gateway changes and an acceptance check that will ping the next-hop using the intended source interface and inspect installed route status before relevant releases.
  2. Require peer review for blackhole route protection changes and an acceptance check that will withdraw the intended tunnel route and verify the protected prefix is not sent to the internet before relevant releases.
  3. Require peer review for sd-wan path diagnostics changes and an acceptance check that will compare health status, service match, and selected member for an affected flow before relevant releases.
  4. Require peer review for performance sla packet loss changes and an acceptance check that will measure link health under controlled loss and verify the voice rule selects an eligible member before relevant releases.

Explanation

Correct Answer

C:

This change-control gate requires teams to require peer review for sd-wan path diagnostics changes and an acceptance check that will compare health status, service match, and selected member for an affected flow before relevant releases, so it catches a repeat of the known misconfiguration before broad deployment. Its success can be checked against the operational evidence to compare health status, service match, and selected member for an affected flow.

Incorrect Answers

A:

A review gate for unreachable static gateway, such as require peer review for unreachable static gateway changes and an acceptance check that will ping the next-hop using the intended source interface and inspect installed route status before relevant releases, can be useful where a static route exists in configuration but traffic cannot reach its specified next-hop gateway, but it is not the approved sd-wan path diagnostics review. The preventive test must enforce that staff will inspect SD-WAN health check status and service-rule decision output for representative flows and subsequently can compare health status, service match, and selected member for an affected flow; the proposed unreachable static gateway gate would not check that same control.

B:

A review gate for blackhole route protection, such as require peer review for blackhole route protection changes and an acceptance check that will withdraw the intended tunnel route and verify the protected prefix is not sent to the internet before relevant releases, can be useful where an intentionally disallowed destination prefix is leaking over a catch-all WAN route when its specific tunnel is absent, but it is not the approved sd-wan path diagnostics review. The preventive test must enforce that staff will inspect SD-WAN health check status and service-rule decision output for representative flows and subsequently can compare health status, service match, and selected member for an affected flow; the proposed blackhole route protection gate would not check that same control.

D:

A review gate for performance sla packet loss, such as require peer review for performance sla packet loss changes and an acceptance check that will measure link health under controlled loss and verify the voice rule selects an eligible member before relevant releases, can be useful where voice calls degrade on a high-loss WAN link while another member meets the application SLA, but it is not the approved sd-wan path diagnostics review. The preventive test must enforce that staff will inspect SD-WAN health check status and service-rule decision output for representative flows and subsequently can compare health status, service match, and selected member for an affected flow; the proposed performance sla packet loss gate would not check that same control.

Question 605

During FortiOS 7.6 operations at a monitored business uplink, the evidence is: Two provider paths seem healthy but one set of applications consistently uses an unexpected member. The operator corrected the configuration by choosing to inspect SD-WAN health check status and service-rule decision output for representative flows. Select TWO answers that together provide a falsifiable acceptance test and a preventive change gate.

  1. Require peer review for sd-wan path diagnostics changes and an acceptance check that will compare health status, service match, and selected member for an affected flow before relevant releases.
  2. Compare health status, service match, and selected member for an affected flow.
  3. Ping the next-hop using the intended source interface and inspect installed route status.
  4. Withdraw the intended tunnel route and verify the protected prefix is not sent to the internet.
  5. Measure link health under controlled loss and verify the voice rule selects an eligible member.

Explanation

Correct Answers

A:

The organization already encountered the failure where two provider paths seem healthy but one set of applications consistently uses an unexpected member, so every relevant future change should be reviewed for the same hazard. Combined with the separate acceptance test to compare health status, service match, and selected member for an affected flow, this gate checks future revisions without claiming that the current configuration is permanently correct.

B:

It measures the operational result after the correction to inspect SD-WAN health check status and service-rule decision output for representative flows, and it directly checks the reported condition: two provider paths seem healthy but one set of applications consistently uses an unexpected member. For sd-wan path diagnostics, a saved profile or healthy dashboard alone would not verify that the affected flow behaves as required.

Incorrect Answers

C:

The proposed evidence, to ping the next-hop using the intended source interface and inspect installed route status, checks unreachable static gateway in a situation such as a static route exists in configuration but traffic cannot reach its specified next-hop gateway, not the required sd-wan path diagnostics acceptance. For the affected firewall behavior the directly discriminating check is to compare health status, service match, and selected member for an affected flow, alongside a review of sd-wan path diagnostics rather than unreachable static gateway settings.

D:

The proposed evidence, to withdraw the intended tunnel route and verify the protected prefix is not sent to the internet, checks blackhole route protection in a situation such as an intentionally disallowed destination prefix is leaking over a catch-all WAN route when its specific tunnel is absent, not the required sd-wan path diagnostics acceptance. For the affected firewall behavior the directly discriminating check is to compare health status, service match, and selected member for an affected flow, alongside a review of sd-wan path diagnostics rather than blackhole route protection settings.

E:

The proposed evidence, to measure link health under controlled loss and verify the voice rule selects an eligible member, checks performance sla packet loss in a situation such as voice calls degrade on a high-loss WAN link while another member meets the application SLA, not the required sd-wan path diagnostics acceptance. For the affected firewall behavior the directly discriminating check is to compare health status, service match, and selected member for an affected flow, alongside a review of sd-wan path diagnostics rather than performance sla packet loss settings.

Question 606

At an internal application segment, a FortiGate running FortiOS 7.6 has this observation: Two branch FortiGates exchange IKE packets but never form a phase-one security association because their IKE versions differ. The requirement concerns ike version agreement while retaining existing unrelated controls. Which FortiGate change MOST directly meets the requirement?

  1. Check IPsec tunnel counters and compare encapsulation and decapsulation with interface packet traces.
  2. Enable compatible NAT traversal and ensure UDP 500 and 4500 reach the correct gateway.
  3. Add an applicable static or dynamic route for the remote private subnet over the IPsec interface.
  4. Configure mutually supported matching IKE version settings on both IPsec peers.

Explanation

Correct Answer

D:

Choosing to configure mutually supported matching IKE version settings on both IPsec peers changes the component implicated by that observation, rather than masking the symptom through a different firewall feature. Operators can substantiate the choice by carrying out this test: inspect IKE negotiation logs and verify the same configured protocol is used at both ends.

Incorrect Answers

A:

Checking IPsec tunnel counters and compare encapsulation and decapsulation with interface packet traces would focus the new configuration on ipsec tunnel packet counters, for which the tunnel widget shows an established connection but users report no application traffic across it may be a valid concern, but this ike version agreement configuration has a different failure. Evidence for ike version agreement requires staff to inspect IKE negotiation logs and verify the same configured protocol is used at both ends; the proposed ipsec tunnel packet counters change cannot deliver that ike version agreement result by itself.

B:

Enabling compatible NAT traversal and ensure UDP 500 and 4500 reach the correct gateway would focus the new configuration on nat traversal for ipsec, for which a branch gateway is behind upstream address translation and the IPsec session cannot reliably use native ESP may be a valid concern, but this ike version agreement configuration has a different failure. Evidence for ike version agreement requires staff to inspect IKE negotiation logs and verify the same configured protocol is used at both ends; the proposed nat traversal for ipsec change cannot deliver that ike version agreement result by itself.

C:

Selecting add an applicable static or dynamic route for the remote private subnet over the IPsec interface would focus the new configuration on vpn route to remote subnet, for which a route-based IPsec tunnel is established but private traffic leaves via the default internet route may be a valid concern, but this ike version agreement configuration has a different failure. Evidence for ike version agreement requires staff to inspect IKE negotiation logs and verify the same configured protocol is used at both ends; the proposed vpn route to remote subnet change cannot deliver that ike version agreement result by itself.

Question 607

A FortiOS 7.6 review of a hybrid-network deployment reports the following condition: Two branch FortiGates exchange IKE packets but never form a phase-one security association because their IKE versions differ. Basic reachability and unrelated systems have already been checked. Which configuration mistake BEST explains this ike version agreement failure?

  1. Require IKEv2 at one gateway while configuring its peer for IKEv1 only.
  2. Assume an established phase-one status proves encrypted user packets travel both directions.
  3. Rely on phase-one negotiation alone to install every required private destination route.
  4. Assume native ESP always traverses an upstream PAT device without NAT traversal.

Explanation

Correct Answer

A:

The problem arises when administrators require IKEv2 at one gateway while configuring its peer for IKEv1 only, so the failing behavior has a concrete configuration cause and is not inferred from an unrelated metric. The relevant repair is to configure mutually supported matching IKE version settings on both IPsec peers.

Incorrect Answers

B:

The alternative cause involving ipsec tunnel packet counters can produce a different failure, for example when the tunnel widget shows an established connection but users report no application traffic across it; it is not the ike version agreement case. The more specific error here is the choice to require IKEv2 at one gateway while configuring its peer for IKEv1 only; check it by attempting to inspect IKE negotiation logs and verify the same configured protocol is used at both ends before making an unrelated ipsec tunnel packet counters change.

C:

The alternative cause involving vpn route to remote subnet can produce a different failure, for example when a route-based IPsec tunnel is established but private traffic leaves via the default internet route; it is not the ike version agreement case. The more specific error here is the choice to require IKEv2 at one gateway while configuring its peer for IKEv1 only; check it by attempting to inspect IKE negotiation logs and verify the same configured protocol is used at both ends before making an unrelated vpn route to remote subnet change.

D:

The alternative cause involving nat traversal for ipsec can produce a different failure, for example when a branch gateway is behind upstream address translation and the IPsec session cannot reliably use native ESP; it is not the ike version agreement case. The more specific error here is the choice to require IKEv2 at one gateway while configuring its peer for IKEv1 only; check it by attempting to inspect IKE negotiation logs and verify the same configured protocol is used at both ends before making an unrelated nat traversal for ipsec change.

Question 608

During FortiOS 7.6 operations at an operations incident response, the evidence is: Two branch FortiGates exchange IKE packets but never form a phase-one security association because their IKE versions differ. Investigators confirmed this cause: administrators chose to require IKEv2 at one gateway while configuring its peer for IKEv1 only. Which action MOST directly corrects the confirmed error?

  1. Configure mutually supported matching IKE version settings on both IPsec peers.
  2. Add an applicable static or dynamic route for the remote private subnet over the IPsec interface.
  3. Check IPsec tunnel counters and compare encapsulation and decapsulation with interface packet traces.
  4. Require IKEv2 at one gateway while configuring its peer for IKEv1 only.

Explanation

Correct Answer

A:

This addresses ike version agreement without needlessly weakening separate security or routing controls. Given the observed condition—two branch FortiGates exchange IKE packets but never form a phase-one security association because their IKE versions differ—the operator should then inspect IKE negotiation logs and verify the same configured protocol is used at both ends.

Incorrect Answers

B:

Changing the mechanism to add an applicable static or dynamic route for the remote private subnet over the IPsec interface could be a sensible correction for vpn route to remote subnet when a route-based IPsec tunnel is established but private traffic leaves via the default internet route. The targeted fix is to configure mutually supported matching IKE version settings on both IPsec peers; a review of vpn route to remote subnet would not, by itself, prove that the team can inspect IKE negotiation logs and verify the same configured protocol is used at both ends.

C:

Changing the mechanism to check IPsec tunnel counters and compare encapsulation and decapsulation with interface packet traces could be a sensible correction for ipsec tunnel packet counters when the tunnel widget shows an established connection but users report no application traffic across it. The targeted fix is to configure mutually supported matching IKE version settings on both IPsec peers; a review of ipsec tunnel packet counters would not, by itself, prove that the team can inspect IKE negotiation logs and verify the same configured protocol is used at both ends.

D:

The proposal repeats the confirmed ike version agreement error by choosing to require IKEv2 at one gateway while configuring its peer for IKEv1 only. A corrective change must instead configure mutually supported matching IKE version settings on both IPsec peers and then produce the measurable result to inspect IKE negotiation logs and verify the same configured protocol is used at both ends; repeating the failed setting cannot serve as a repair.

Question 609

At a network segmentation review, a FortiGate running FortiOS 7.6 has this observation: Two branch FortiGates exchange IKE packets but never form a phase-one security association because their IKE versions differ. The incident has been fixed, and the owner wants to prevent a recurrence of the ike version agreement problem. Which future change-control rule is MOST appropriate?

  1. Require peer review for nat traversal for ipsec changes and an acceptance check that will observe UDP-encapsulated IPsec negotiation and successful tunnel traffic behind the NAT before relevant releases.
  2. Require peer review for ike version agreement changes and an acceptance check that will inspect IKE negotiation logs and verify the same configured protocol is used at both ends before relevant releases.
  3. Require peer review for ipsec tunnel packet counters changes and an acceptance check that will send a controlled cross-site packet and compare inbound and outbound encrypted counters before relevant releases.
  4. Require peer review for vpn route to remote subnet changes and an acceptance check that will inspect the selected route for a remote host and verify egress on the tunnel interface before relevant releases.

Explanation

Correct Answer

B:

This change-control gate requires teams to require peer review for ike version agreement changes and an acceptance check that will inspect IKE negotiation logs and verify the same configured protocol is used at both ends before relevant releases, so it catches a repeat of the known misconfiguration before broad deployment. Its success can be checked against the operational evidence to inspect IKE negotiation logs and verify the same configured protocol is used at both ends.

Incorrect Answers

A:

A review gate for nat traversal for ipsec, such as require peer review for nat traversal for ipsec changes and an acceptance check that will observe UDP-encapsulated IPsec negotiation and successful tunnel traffic behind the NAT before relevant releases, can be useful where a branch gateway is behind upstream address translation and the IPsec session cannot reliably use native ESP, but it is not the approved ike version agreement review. The preventive test must enforce that staff will configure mutually supported matching IKE version settings on both IPsec peers and subsequently can inspect IKE negotiation logs and verify the same configured protocol is used at both ends; the proposed nat traversal for ipsec gate would not check that same control.

C:

A review gate for ipsec tunnel packet counters, such as require peer review for ipsec tunnel packet counters changes and an acceptance check that will send a controlled cross-site packet and compare inbound and outbound encrypted counters before relevant releases, can be useful where the tunnel widget shows an established connection but users report no application traffic across it, but it is not the approved ike version agreement review. The preventive test must enforce that staff will configure mutually supported matching IKE version settings on both IPsec peers and subsequently can inspect IKE negotiation logs and verify the same configured protocol is used at both ends; the proposed ipsec tunnel packet counters gate would not check that same control.

D:

A review gate for vpn route to remote subnet, such as require peer review for vpn route to remote subnet changes and an acceptance check that will inspect the selected route for a remote host and verify egress on the tunnel interface before relevant releases, can be useful where a route-based IPsec tunnel is established but private traffic leaves via the default internet route, but it is not the approved ike version agreement review. The preventive test must enforce that staff will configure mutually supported matching IKE version settings on both IPsec peers and subsequently can inspect IKE negotiation logs and verify the same configured protocol is used at both ends; the proposed vpn route to remote subnet gate would not check that same control.

Question 610

A FortiOS 7.6 review of a managed branch perimeter reports the following condition: Two branch FortiGates exchange IKE packets but never form a phase-one security association because their IKE versions differ. The operator corrected the configuration by choosing to configure mutually supported matching IKE version settings on both IPsec peers. Select TWO answers that together provide a falsifiable acceptance test and a preventive change gate.

  1. Inspect the selected route for a remote host and verify egress on the tunnel interface.
  2. Require peer review for ike version agreement changes and an acceptance check that will inspect IKE negotiation logs and verify the same configured protocol is used at both ends before relevant releases.
  3. Observe UDP-encapsulated IPsec negotiation and successful tunnel traffic behind the NAT.
  4. Inspect IKE negotiation logs and verify the same configured protocol is used at both ends.
  5. Send a controlled cross-site packet and compare inbound and outbound encrypted counters.

Explanation

Correct Answers

B:

The organization already encountered the failure where two branch FortiGates exchange IKE packets but never form a phase-one security association because their IKE versions differ, so every relevant future change should be reviewed for the same hazard. Combined with the separate acceptance test to inspect IKE negotiation logs and verify the same configured protocol is used at both ends, this gate checks future revisions without claiming that the current configuration is permanently correct.

D:

It measures the operational result after the correction to configure mutually supported matching IKE version settings on both IPsec peers, and it directly checks the reported condition: two branch FortiGates exchange IKE packets but never form a phase-one security association because their IKE versions differ. For ike version agreement, a saved profile or healthy dashboard alone would not verify that the affected flow behaves as required.

Incorrect Answers

A:

The proposed evidence, to inspect the selected route for a remote host and verify egress on the tunnel interface, checks vpn route to remote subnet in a situation such as a route-based IPsec tunnel is established but private traffic leaves via the default internet route, not the required ike version agreement acceptance. For the affected firewall behavior the directly discriminating check is to inspect IKE negotiation logs and verify the same configured protocol is used at both ends, alongside a review of ike version agreement rather than vpn route to remote subnet settings.

C:

The proposed evidence, to observe UDP-encapsulated IPsec negotiation and successful tunnel traffic behind the NAT, checks nat traversal for ipsec in a situation such as a branch gateway is behind upstream address translation and the IPsec session cannot reliably use native ESP, not the required ike version agreement acceptance. For the affected firewall behavior the directly discriminating check is to inspect IKE negotiation logs and verify the same configured protocol is used at both ends, alongside a review of ike version agreement rather than nat traversal for ipsec settings.

E:

The proposed evidence, to send a controlled cross-site packet and compare inbound and outbound encrypted counters, checks ipsec tunnel packet counters in a situation such as the tunnel widget shows an established connection but users report no application traffic across it, not the required ike version agreement acceptance. For the affected firewall behavior the directly discriminating check is to inspect IKE negotiation logs and verify the same configured protocol is used at both ends, alongside a review of ike version agreement rather than ipsec tunnel packet counters settings.

Fortinet NSE 4 - FortiOS 7.6 Administrator (NSE4_FGT_AD-7.6) Practice Tests