Practice Exams:

Fortinet FCP_FGT_AD-7.6 Dumps

EXAM: FCP - FortiGate 7.6 Administrator
Verified By Experts
Premium Bundle
$49.99

FCP_FGT_AD-7.6 Premium ETE File


  • Premium File 128 Questions & Answers
Whats Included:
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

Fortinet FCP_FGT_AD-7.6 Practice Test 56

Question 550

A regional accounting team can establish IPsec to its backup office but no file-share sessions cross the tunnel. Which combined implementation and verification plan most reliably resolves this specific FortiOS 7.6 issue?

  1. For the regional accounting team deployment: Implement: Compare IKE version, authentication method, proposals and peer addresses at both IPsec endpoints before changing unrelated firewall rules. Verify: Inspect both peers' IKE negotiation logs and confirm a stable phase-one SA after matching supported parameters.
  2. For the regional accounting team deployment: Implement: Configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks. Verify: Verify tunnel interface and route status, send a packet to the remote protected prefix and check matching policy and tunnel byte counters.
  3. For the regional accounting team deployment: Implement: Align both peers' protected traffic selectors and phase-two proposals for the intended site-to-site prefixes. Verify: Verify tunnel interface and route status, send a packet to the remote protected prefix and check matching policy and tunnel byte counters.
  4. For the regional accounting team deployment: Implement: Configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks. Verify: Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

Answer & Explanations

Correct answer: B

A.

The situation is that a regional accounting team can establish IPsec to its backup office but no file-share sessions cross the tunnel. This action and check address the distinct objective “Repair mismatched IKE phase-one proposals” instead of the stated acceptance requirement. The matching action is to configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks. Its confirming test is to verify tunnel interface and route status, send a packet to the remote protected prefix and check matching policy and tunnel byte counters.

B.

The situation is that a regional accounting team can establish IPsec to its backup office but no file-share sessions cross the tunnel. Implement: Configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks. Verify: Verify tunnel interface and route status, send a packet to the remote protected prefix and check matching policy and tunnel byte counters. This pairing is justified because an established IPsec tunnel alone does not tell FortiOS to forward selected traffic through it or permit that traffic through security policy.

C.

This action and check address the alternate operation “For the regional accounting team deployment: Implement: Align both peers' protected traffic selectors and phase-two proposals for the intended…” instead of the stated acceptance requirement. The matching action is to configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks. Its confirming test is to verify tunnel interface and route status, send a packet to the remote protected prefix and check matching policy and tunnel byte counters.

D.

This action and check address the alternate operation “For the regional accounting team deployment: Implement: Configure an interface-based IPsec tunnel with a route and bidirectional firewall policy…” instead of the stated acceptance requirement. The matching action is to configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks. Its confirming test is to verify tunnel interface and route status, send a packet to the remote protected prefix and check matching policy and tunnel byte counters.

Question 551

A rural branch's FortiGate sits behind its provider's address translator and an otherwise correct VPN never carries payload. Which FortiOS 7.6 administrative change best meets this requirement without weakening unrelated controls?

  1. For the rural branch's FortiGate deployment: Align both peers' protected traffic selectors and phase-two proposals for the intended site-to-site prefixes.
  2. For the rural branch's FortiGate deployment: Configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks.
  3. For the rural branch's FortiGate deployment: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation.
  4. For the rural branch's FortiGate deployment: Tune supported dead peer detection and recovery behavior appropriate to a tunnel's expected intermittent connectivity.

Answer & Explanations

Correct answer: C

A.

This option addresses the distinct objective “Match IPsec phase-two selectors and transforms”, not the immediate requirement. Even with successful IKE phase one, incompatible phase-two selectors or transform proposals can prevent establishing usable IPsec child SAs. For the stated case, NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

B.

This option addresses the distinct objective “Add route and policy for an interface-based IPsec tunnel”, not the immediate requirement. An established IPsec tunnel alone does not tell FortiOS to forward selected traffic through it or permit that traffic through security policy. For the stated case, NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

C.

Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. This resolves the issue because NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data. To verify, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

D.

This option addresses the distinct objective “Use dead peer detection to clear broken sessions”, not the immediate requirement. DPD identifies an unresponsive IKE peer so stale SAs can be cleared and re-established; it does not replace routing or persistent tunnel monitoring. For the stated case, NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

Question 552

A rural branch's FortiGate sits behind its provider's address translator and an otherwise correct VPN never carries payload. The engineer proposes this change: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation Which explanation most accurately establishes why that change meets the operational requirement?

  1. For the rural branch's FortiGate deployment: An established IPsec tunnel alone does not tell FortiOS to forward selected traffic through it or permit that traffic through security policy.
  2. For the rural branch's FortiGate deployment: DPD identifies an unresponsive IKE peer so stale SAs can be cleared and re-established; it does not replace routing or persistent tunnel monitoring.
  3. For the rural branch's FortiGate deployment: Even with successful IKE phase one, incompatible phase-two selectors or transform proposals can prevent establishing usable IPsec child SAs.
  4. For the rural branch's FortiGate deployment: NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

Answer & Explanations

Correct answer: D

A.

That statement explains the distinct objective “Add route and policy for an interface-based IPsec tunnel” rather than the cause in this case. The deciding mechanism here is that NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

B.

That statement explains the distinct objective “Use dead peer detection to clear broken sessions” rather than the cause in this case. The deciding mechanism here is that NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

C.

That statement explains the distinct objective “Match IPsec phase-two selectors and transforms” rather than the cause in this case. The deciding mechanism here is that NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

D.

NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data. It supports this action: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. To confirm, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

Question 553

A rural branch's FortiGate sits behind its provider's address translator and an otherwise correct VPN never carries payload. After implementing this change—Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation—which test best establishes that the intended outcome is actually working?

  1. For the rural branch's FortiGate deployment: Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.
  2. For the rural branch's FortiGate deployment: Verify tunnel interface and route status, send a packet to the remote protected prefix and check matching policy and tunnel byte counters.
  3. For the rural branch's FortiGate deployment: Disconnect the remote peer briefly and observe DPD events, SA state change and successful renegotiation after connectivity returns.
  4. For the rural branch's FortiGate deployment: Inspect phase-two negotiations, child SA selectors and byte counters while sending a controlled packet between the protected subnets.

Answer & Explanations

Correct answer: A

A.

Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance. This is the relevant test because NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

B.

This check would help evaluate the distinct objective “Add route and policy for an interface-based IPsec tunnel”, but not the required result. For this case, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

C.

This check would help evaluate the distinct objective “Use dead peer detection to clear broken sessions”, but not the required result. For this case, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

D.

This check would help evaluate the distinct objective “Match IPsec phase-two selectors and transforms”, but not the required result. For this case, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

Question 554

A rural branch's FortiGate sits behind its provider's address translator and an otherwise correct VPN never carries payload. Which proposed shortcut would most directly cause failed or unstable IPsec traffic through the translating device, and therefore must be avoided for this requirement?

  1. For the rural branch's FortiGate deployment: Assume successful IKE negotiation automatically installs every missing route and allow policy.
  2. For the rural branch's FortiGate deployment: Permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation.
  3. For the rural branch's FortiGate deployment: Set the tunnel to trust stale SAs indefinitely whenever the peer goes offline.
  4. For the rural branch's FortiGate deployment: Treat a green phase-one status icon as proof that every protected subnet has an established phase-two SA.

Answer & Explanations

Correct answer: B

A.

That shortcut would relate to the distinct objective “Add route and policy for an interface-based IPsec tunnel”, rather than the specific configuration or use described. The unsafe step in this case is to permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation.

B.

Permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation. The proposed shortcut bypasses the needed control: NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data. The appropriate response is to check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation.

C.

That shortcut would relate to the distinct objective “Use dead peer detection to clear broken sessions”, rather than the specific configuration or use described. The unsafe step in this case is to permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation.

D.

That shortcut would relate to the distinct objective “Match IPsec phase-two selectors and transforms”, rather than the specific configuration or use described. The unsafe step in this case is to permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation.

Question 555

A rural branch's FortiGate sits behind its provider's address translator and an otherwise correct VPN never carries payload. Which combined implementation and verification plan most reliably resolves this specific FortiOS 7.6 issue?

  1. For the rural branch's FortiGate deployment: Implement: Configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks. Verify: Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.
  2. For the rural branch's FortiGate deployment: Implement: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Verify: Disconnect the remote peer briefly and observe DPD events, SA state change and successful renegotiation after connectivity returns.
  3. For the rural branch's FortiGate deployment: Implement: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Verify: Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.
  4. For the rural branch's FortiGate deployment: Implement: Align both peers' protected traffic selectors and phase-two proposals for the intended site-to-site prefixes. Verify: Inspect phase-two negotiations, child SA selectors and byte counters while sending a controlled packet between the protected subnets.

Answer & Explanations

Correct answer: C

A.

This action and check address the alternate operation “For the rural branch's FortiGate deployment: Implement: Configure an interface-based IPsec tunnel with a route and bidirectional firewall policy…” instead of the stated acceptance requirement. The matching action is to check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Its confirming test is to trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

B.

This action and check address the alternate operation “For the rural branch's FortiGate deployment: Implement: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec…” instead of the stated acceptance requirement. The matching action is to check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Its confirming test is to trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

C.

Implement: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Verify: Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance. This pairing is justified because NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

D.

This action and check address the distinct objective “Match IPsec phase-two selectors and transforms” instead of the stated acceptance requirement. The matching action is to check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Its confirming test is to trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

Question 556

A research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. Which FortiOS 7.6 administrative change best meets this requirement without weakening unrelated controls?

  1. For the research vessel's satellite modem deployment: Tune supported dead peer detection and recovery behavior appropriate to a tunnel's expected intermittent connectivity.
  2. For the research vessel's satellite modem deployment: Align both peers' protected traffic selectors and phase-two proposals for the intended site-to-site prefixes.
  3. For the research vessel's satellite modem deployment: Configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks.
  4. For the research vessel's satellite modem deployment: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation.

Answer & Explanations

Correct answer: D

A.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. This option addresses the distinct objective “Use dead peer detection to clear broken sessions”, not the immediate requirement. DPD identifies an unresponsive IKE peer so stale SAs can be cleared and re-established; it does not replace routing or persistent tunnel monitoring. For the stated case, NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

B.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. This option addresses the distinct objective “Match IPsec phase-two selectors and transforms”, not the immediate requirement. Even with successful IKE phase one, incompatible phase-two selectors or transform proposals can prevent establishing usable IPsec child SAs. For the stated case, NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

C.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. This option addresses the distinct objective “Add route and policy for an interface-based IPsec tunnel”, not the immediate requirement. An established IPsec tunnel alone does not tell FortiOS to forward selected traffic through it or permit that traffic through security policy. For the stated case, NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

D.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. This resolves the issue because NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data. To verify, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

Question 557

A research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. The engineer proposes this change: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation Which explanation most accurately establishes why that change meets the operational requirement?

  1. For the research vessel's satellite modem deployment: NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.
  2. For the research vessel's satellite modem deployment: DPD identifies an unresponsive IKE peer so stale SAs can be cleared and re-established; it does not replace routing or persistent tunnel monitoring.
  3. For the research vessel's satellite modem deployment: Even with successful IKE phase one, incompatible phase-two selectors or transform proposals can prevent establishing usable IPsec child SAs.
  4. For the research vessel's satellite modem deployment: An established IPsec tunnel alone does not tell FortiOS to forward selected traffic through it or permit that traffic through security policy.

Answer & Explanations

Correct answer: A

A.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data. It supports this action: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. To confirm, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

B.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. That statement explains the distinct objective “Use dead peer detection to clear broken sessions” rather than the cause in this case. The deciding mechanism here is that NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

C.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. That statement explains the distinct objective “Match IPsec phase-two selectors and transforms” rather than the cause in this case. The deciding mechanism here is that NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

D.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. That statement explains the distinct objective “Add route and policy for an interface-based IPsec tunnel” rather than the cause in this case. The deciding mechanism here is that NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

Question 558

A research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. After implementing this change—Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation—which test best establishes that the intended outcome is actually working?

  1. For the research vessel's satellite modem deployment: Disconnect the remote peer briefly and observe DPD events, SA state change and successful renegotiation after connectivity returns.
  2. For the research vessel's satellite modem deployment: Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.
  3. For the research vessel's satellite modem deployment: Inspect phase-two negotiations, child SA selectors and byte counters while sending a controlled packet between the protected subnets.
  4. For the research vessel's satellite modem deployment: Verify tunnel interface and route status, send a packet to the remote protected prefix and check matching policy and tunnel byte counters.

Answer & Explanations

Correct answer: B

A.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. This check would help evaluate the distinct objective “Use dead peer detection to clear broken sessions”, but not the required result. For this case, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

B.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance. This is the relevant test because NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

C.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. This check would help evaluate the distinct objective “Match IPsec phase-two selectors and transforms”, but not the required result. For this case, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

D.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. This check would help evaluate the distinct objective “Add route and policy for an interface-based IPsec tunnel”, but not the required result. For this case, trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

Question 559

A research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. Which proposed shortcut would most directly cause failed or unstable IPsec traffic through the translating device, and therefore must be avoided for this requirement?

  1. For the research vessel's satellite modem deployment: Set the tunnel to trust stale SAs indefinitely whenever the peer goes offline.
  2. For the research vessel's satellite modem deployment: Treat a green phase-one status icon as proof that every protected subnet has an established phase-two SA.
  3. For the research vessel's satellite modem deployment: Permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation.
  4. For the research vessel's satellite modem deployment: Assume successful IKE negotiation automatically installs every missing route and allow policy.

Answer & Explanations

Correct answer: C

A.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. That shortcut would relate to the distinct objective “Use dead peer detection to clear broken sessions”, rather than the specific configuration or use described. The unsafe step in this case is to permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation.

B.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. That shortcut would relate to the distinct objective “Match IPsec phase-two selectors and transforms”, rather than the specific configuration or use described. The unsafe step in this case is to permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation.

C.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. Permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation. The proposed shortcut bypasses the needed control: NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data. The appropriate response is to check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation.

D.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. That shortcut would relate to the distinct objective “Add route and policy for an interface-based IPsec tunnel”, rather than the specific configuration or use described. The unsafe step in this case is to permit only unencapsulated ESP through an upstream NAT while blocking required UDP negotiation.

Question 560

A research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. Which combined implementation and verification plan most reliably resolves this specific FortiOS 7.6 issue?

  1. For the research vessel's satellite modem deployment: Implement: Align both peers' protected traffic selectors and phase-two proposals for the intended site-to-site prefixes. Verify: Inspect phase-two negotiations, child SA selectors and byte counters while sending a controlled packet between the protected subnets.
  2. For the research vessel's satellite modem deployment: Implement: Configure an interface-based IPsec tunnel with a route and bidirectional firewall policy matching the intended protected networks. Verify: Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.
  3. For the research vessel's satellite modem deployment: Implement: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Verify: Disconnect the remote peer briefly and observe DPD events, SA state change and successful renegotiation after connectivity returns.
  4. For the research vessel's satellite modem deployment: Implement: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Verify: Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

Answer & Explanations

Correct answer: D

A.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. This action and check address the distinct objective “Match IPsec phase-two selectors and transforms” instead of the stated acceptance requirement. The matching action is to check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Its confirming test is to trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

B.

This action and check address the alternate operation “For the research vessel's satellite modem deployment: Implement: Configure an interface-based IPsec tunnel with a route and bidirectional firewall…” instead of the stated acceptance requirement. The matching action is to check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Its confirming test is to trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

C.

This action and check address the alternate operation “For the research vessel's satellite modem deployment: Implement: Check UDP 500/4500 path and supported NAT traversal settings when an…” instead of the stated acceptance requirement. The matching action is to check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Its confirming test is to trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance.

D.

The situation is that a research vessel's satellite modem performs NAT before site-to-site VPN traffic reaches headquarters. Implement: Check UDP 500/4500 path and supported NAT traversal settings when an IPsec peer sits behind address translation. Verify: Trace the peer handshake and UDP port negotiation on both sides of the NAT device, then confirm encrypted byte counters advance. This pairing is justified because NAT traversal encapsulates ESP in UDP 4500 where negotiated and needed; an intermediary that drops required IKE or UDP-encapsulated traffic can break tunnel establishment or data.

FCP - FortiGate 7.6 Administrator (FCP_FGT_AD-7.6) Practice Tests