Cisco 400-007 Dumps
Cisco 400-007 Practice Test 39
Question 380
A network design team is assessing this customer situation: Two redundant core chassis share the same power feed and software release fault exposure. An approved alternate path exists, but its cost and policy limits differ. Which failure is the most direct risk of taking the tempting design shortcut?
Answer & Explanations
Correct answer: D
The offered consequence belongs to the alternative control path: Use L1/L2 boundaries and leak only policy-approved interlevel routes. The relevant failure for the current situation is: One common-mode event can remove both paths at once. The distinction follows from: Redundant device counts are insufficient when resources share correlated failure modes.
The offered consequence belongs to the alternative control path: Tune BFD intervals to measured platform and transport behavior with appropriate headroom. The relevant failure for the current situation is: One common-mode event can remove both paths at once. The distinction follows from: Redundant device counts are insufficient when resources share correlated failure modes.
The offered consequence belongs to the alternative control path: Create area boundaries and resilient ABRs that localize topology changes without isolating reachability. The relevant failure for the current situation is: One common-mode event can remove both paths at once. The distinction follows from: Redundant device counts are insufficient when resources share correlated failure modes.
One common-mode event can remove both paths at once. That is the risk in the reported situation—Two redundant core chassis share the same power feed and software release fault exposure. The corrective action is: Design independently powered, physically separated paths with tested software and device fate boundaries. Technical basis: Redundant device counts are insufficient when resources share correlated failure modes.
Question 381
In a separate customer architecture review, this issue arises: A data center moves to dual fabrics but both connect through one shared interconnect device. Recovery operations depend on teams in different geographic regions. Which technical rationale best explains the proposed design choice under these constraints?
Answer & Explanations
Correct answer: A
Redundant device counts are insufficient when resources share correlated failure modes. This explains the action: Design independently powered, physically separated paths with tested software and device fate boundaries. For the described facts—A data center moves to dual fabrics but both connect through one shared interconnect device—test the outcome through: An intentional failure of one power or fabric domain preserves the defined critical flows.
The alternative principle is: OSPF flooding domains and summary design affect CPU load, SPF frequency and fault propagation. It instead explains this action: Create area boundaries and resilient ABRs that localize topology changes without isolating reachability. For the present requirement, the controlling mechanism is: Redundant device counts are insufficient when resources share correlated failure modes. The scenario is: A data center moves to dual fabrics but both connect through one shared interconnect device.
The alternative principle is: Smaller broadcast domains and loop controls constrain accidental Layer 2 topology changes. It instead explains this action: Limit access-layer L2 domains and use routed distribution boundaries with edge-loop safeguards. For the present requirement, the controlling mechanism is: Redundant device counts are insufficient when resources share correlated failure modes.
The alternative principle is: Probabilistic prediction should not replace deterministic routing safety and change authorization. It instead explains this action: Use AI recommendations as evidence with simulation and gated human-controlled network changes. For the present requirement, the controlling mechanism is: Redundant device counts are insufficient when resources share correlated failure modes.
Question 382
In a separate customer architecture review, this issue arises: A data center moves to dual fabrics but both connect through one shared interconnect device. Recovery operations depend on teams in different geographic regions. Which acceptance result would most convincingly demonstrate that the design addresses the critical requirement?
Answer & Explanations
Correct answer: B
The offered observation would test: Create area boundaries and resilient ABRs that localize topology changes without isolating reachability. It would not establish that the stated requirement has been met. The direct evidence needed here is: An intentional failure of one power or fabric domain preserves the defined critical flows.
Direct verification: An intentional failure of one power or fabric domain preserves the defined critical flows. This is the relevant evidence for the action: Design independently powered, physically separated paths with tested software and device fate boundaries. The reason is: Redundant device counts are insufficient when resources share correlated failure modes. The scenario is: A data center moves to dual fabrics but both connect through one shared interconnect device.
The offered observation would test: Use AI recommendations as evidence with simulation and gated human-controlled network changes. It would not establish that the stated requirement has been met. The direct evidence needed here is: An intentional failure of one power or fabric domain preserves the defined critical flows.
The offered observation would test: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. It would not establish that the stated requirement has been met. The direct evidence needed here is: An intentional failure of one power or fabric domain preserves the defined critical flows.
Question 383
In a separate customer architecture review, this issue arises: A data center moves to dual fabrics but both connect through one shared interconnect device. Recovery operations depend on teams in different geographic regions. Which failure is the most direct risk of taking the tempting design shortcut?
Answer & Explanations
Correct answer: C
The offered consequence belongs to the alternative control path: Implement documented local preference and community policy at controlled BGP boundaries. The relevant failure for the current situation is: One common-mode event can remove both paths at once. The distinction follows from: Redundant device counts are insufficient when resources share correlated failure modes.
The offered consequence belongs to the alternative control path: Create area boundaries and resilient ABRs that localize topology changes without isolating reachability. The relevant failure for the current situation is: One common-mode event can remove both paths at once. The distinction follows from: Redundant device counts are insufficient when resources share correlated failure modes. The scenario is: A data center moves to dual fabrics but both connect through one shared interconnect device.
One common-mode event can remove both paths at once. That is the risk in the reported situation—A data center moves to dual fabrics but both connect through one shared interconnect device. The corrective action is: Design independently powered, physically separated paths with tested software and device fate boundaries. Technical basis: Redundant device counts are insufficient when resources share correlated failure modes.
The offered consequence belongs to the alternative control path: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. The relevant failure for the current situation is: One common-mode event can remove both paths at once. The distinction follows from: Redundant device counts are insufficient when resources share correlated failure modes.
Question 384
In a separate customer architecture review, this issue arises: A data center moves to dual fabrics but both connect through one shared interconnect device. Recovery operations depend on teams in different geographic regions. Which prerequisite should the architect confirm before choosing and defending this design?
Answer & Explanations
Correct answer: D
The offered preparation belongs with the alternative action: Create area boundaries and resilient ABRs that localize topology changes without isolating reachability. Here the necessary starting condition is: Obtain dependency diagrams, firmware diversity policy and maintenance interaction constraints. It supports: Design independently powered, physically separated paths with tested software and device fate boundaries.
The offered preparation belongs with the alternative action: Use AI recommendations as evidence with simulation and gated human-controlled network changes. Here the necessary starting condition is: Obtain dependency diagrams, firmware diversity policy and maintenance interaction constraints. It supports: Design independently powered, physically separated paths with tested software and device fate boundaries.
The offered preparation belongs with the alternative action: Limit access-layer L2 domains and use routed distribution boundaries with edge-loop safeguards. Here the necessary starting condition is: Obtain dependency diagrams, firmware diversity policy and maintenance interaction constraints. It supports: Design independently powered, physically separated paths with tested software and device fate boundaries.
The necessary starting condition is: Obtain dependency diagrams, firmware diversity policy and maintenance interaction constraints. This enables the action: Design independently powered, physically separated paths with tested software and device fate boundaries. Validate the result with: An intentional failure of one power or fabric domain preserves the defined critical flows.
Question 385
A network design team is assessing this customer situation: A brownfield network migration must change core routing and access control in one evening. Changes to security policy must be approved by an independent owner. Which high-level network design choice most directly meets the stated technical and operational requirement?
Answer & Explanations
Correct answer: A
Explicit go/no-go measurements allow reversible progress before hidden state diverges too far. For the documented situation—A brownfield network migration must change core routing and access control in one evening—the targeted response is: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. Check: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event.
The alternative addresses: Design independently powered, physically separated paths with tested software and device fate boundaries. Its principle is: Redundant device counts are insufficient when resources share correlated failure modes. In this case the needed action is: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. Confirm by: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event.
The alternative addresses a different technical concern: Business expansion changes administrative domains, latency demands and allowed traffic paths. The governing mechanism here is: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far. Accordingly, use: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency.
EVPN route advertisement can limit flooding and signal endpoint changes through control-plane state. That supports the alternative intervention: Use control-plane learned endpoint reachability with bounded mobility and ARP or ND suppression policies. The present situation—A brownfield network migration must change core routing and access control in one evening—instead calls for: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. Technical basis: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
Question 386
A network design team is assessing this customer situation: A brownfield network migration must change core routing and access control in one evening. Changes to security policy must be approved by an independent owner. Which acceptance result would most convincingly demonstrate that the design addresses the critical requirement?
Answer & Explanations
Correct answer: B
The offered observation would test: Separate reusable intent modules from region variables and enforce code ownership and review contracts. It would not establish that the stated requirement has been met. The direct evidence needed here is: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event.
Direct verification: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event. This is the relevant evidence for the action: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. The reason is: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
The offered observation would test: Use a time-bounded dual-running migration with explicit route authority and per-site cutover controls. It would not establish that the stated requirement has been met. The direct evidence needed here is: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event.
The offered observation would test: Define regional route, policy and service boundaries from business geography and data constraints. It would not establish that the stated requirement has been met. The direct evidence needed here is: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event.
Question 387
A network design team is assessing this customer situation: A brownfield network migration must change core routing and access control in one evening. Changes to security policy must be approved by an independent owner. Which failure is the most direct risk of taking the tempting design shortcut?
Answer & Explanations
Correct answer: C
The offered consequence belongs to the alternative control path: Partition modules by failure, ownership and change cadence with carefully designed routed boundaries. The relevant failure for the current situation is: Rollback can create split configurations and prolonged service unavailability. The distinction follows from: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
The offered consequence belongs to the alternative control path: Separate reusable intent modules from region variables and enforce code ownership and review contracts. The relevant failure for the current situation is: Rollback can create split configurations and prolonged service unavailability. The distinction follows from: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
Rollback can create split configurations and prolonged service unavailability. That is the risk in the reported situation—A brownfield network migration must change core routing and access control in one evening. The corrective action is: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. Technical basis: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
The offered consequence belongs to the alternative control path: Use control-plane learned endpoint reachability with bounded mobility and ARP or ND suppression policies. The relevant failure for the current situation is: Rollback can create split configurations and prolonged service unavailability. The distinction follows from: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
Question 388
A network design team is assessing this customer situation: A brownfield network migration must change core routing and access control in one evening. Changes to security policy must be approved by an independent owner. Which prerequisite should the architect confirm before choosing and defending this design?
Answer & Explanations
Correct answer: D
The offered preparation belongs with the alternative action: Define regional route, policy and service boundaries from business geography and data constraints. Here the necessary starting condition is: Agree backup validity, service checkpoints, authorized abort owner and maximum outage. It supports: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency.
The offered preparation belongs with the alternative action: Separate reusable intent modules from region variables and enforce code ownership and review contracts. Here the necessary starting condition is: Agree backup validity, service checkpoints, authorized abort owner and maximum outage. It supports: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency.
The offered preparation belongs with the alternative action: Design first-hop protections for router advertisements and neighbor discovery on supported access switches. Here the necessary starting condition is: Agree backup validity, service checkpoints, authorized abort owner and maximum outage. It supports: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency.
The necessary starting condition is: Agree backup validity, service checkpoints, authorized abort owner and maximum outage. This enables the action: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. Validate the result with: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event.
Question 389
In a separate customer architecture review, this issue arises: A regulated enterprise cannot tolerate an unplanned return to a partially converted topology. The operational team has limited access to a remote carrier demarcation. Which high-level network design choice most directly meets the stated technical and operational requirement?
Answer & Explanations
Correct answer: A
Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. The relevant technical reason is: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far. Confirm through: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event.
The alternative addresses a different technical concern: Coexistence protects service continuity only when route ownership and address overlaps are resolved. The governing mechanism here is: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far. Accordingly, use: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency.
A Clos topology scales horizontal capacity by adding equal-cost fabric paths rather than funneling traffic through one choke point. That supports the alternative intervention: Use a scalable leaf-spine fabric with designed ECMP paths and explicit oversubscription targets. The present situation—A regulated enterprise cannot tolerate an unplanned return to a partially converted topology—instead calls for: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. Technical basis: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
The alternative addresses: Tune BFD intervals to measured platform and transport behavior with appropriate headroom. Its principle is: Failure detection should be fast enough for objectives without causing false neighbor losses during transient congestion. In this case the needed action is: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. Confirm by: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event.
Question 390
In a separate customer architecture review, this issue arises: A regulated enterprise cannot tolerate an unplanned return to a partially converted topology. The operational team has limited access to a remote carrier demarcation. Which technical rationale best explains the proposed design choice under these constraints?
Answer & Explanations
Correct answer: B
The alternative principle is: Coexistence protects service continuity only when route ownership and address overlaps are resolved. It instead explains this action: Use a time-bounded dual-running migration with explicit route authority and per-site cutover controls. For the present requirement, the controlling mechanism is: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
Explicit go/no-go measurements allow reversible progress before hidden state diverges too far. This explains the action: Define prechange snapshots, staged checkpoints and objective rollback triggers for each dependency. For the described facts—A regulated enterprise cannot tolerate an unplanned return to a partially converted topology—test the outcome through: A timed rehearsal restores original forwarding, ACL policy and sessions after a declared abort event.
The alternative principle is: IPv6 hosts rely on ND and RA control messages; unauthenticated or unrestricted advertisements can redirect clients. It instead explains this action: Design first-hop protections for router advertisements and neighbor discovery on supported access switches. For the present requirement, the controlling mechanism is: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
The alternative principle is: A Clos topology scales horizontal capacity by adding equal-cost fabric paths rather than funneling traffic through one choke point. It instead explains this action: Use a scalable leaf-spine fabric with designed ECMP paths and explicit oversubscription targets. For the present requirement, the controlling mechanism is: Explicit go/no-go measurements allow reversible progress before hidden state diverges too far.
Cisco Certified Design Expert (400-007) Practice Tests
- Cisco 400-007 Practice Test 37 - 10 Questions (Last Reviewed 13-Oct-2026)
- Cisco 400-007 Practice Test 38 - 10 Questions (Last Reviewed 12-Oct-2026)
- Cisco 400-007 Practice Test 39 - 10 Questions (Last Reviewed 11-Oct-2026)
- Cisco 400-007 Practice Test 40 - 10 Questions (Last Reviewed 10-Oct-2026)
- Cisco 400-007 Practice Test 41 - 10 Questions (Last Reviewed 09-Oct-2026)