Practice Exams:

Cisco 400-007 Dumps

EXAM: Cisco Certified Design Expert
Verified By Experts
Premium Bundle
$19.99
$54.99 $74.98

400-007 Premium Bundle


  • Premium File 349 Questions & Answers
  • Study Guide 934 Pages

Cisco 400-007 Practice Test 25

Question 240

In a separate customer architecture review, this issue arises: A provider deploys a new routing template to thousands of devices with uncertain hardware parity. A fixed procurement ceiling rules out indefinite capacity overprovisioning. Which failure is the most direct risk of taking the tempting design shortcut?

  1. Operational errors and control-plane state can grow faster than deployment capacity
  2. Monitoring and configuration jobs can silently misinterpret interfaces or routing intent
  3. Partially applied network changes can survive despite an apparently successful automation run
  4. A platform-specific defect can affect the entire fleet before operators can isolate the cause

Answer & Explanations

Correct answer: D

A.

The offered consequence belongs to the alternative control path: Partition routing domains or apply hierarchy while standardizing policy templates and validation. The relevant failure for the current situation is: A platform-specific defect can affect the entire fleet before operators can isolate the cause. The distinction follows from: Limited blast radius and observable acceptance criteria avoid a simultaneous fleet-wide regression.

B.

The offered consequence belongs to the alternative control path: Pin schema versions and test contract compatibility before controller or device upgrades. The relevant failure for the current situation is: A platform-specific defect can affect the entire fleet before operators can isolate the cause. The distinction follows from: Limited blast radius and observable acceptance criteria avoid a simultaneous fleet-wide regression.

C.

The offered consequence belongs to the alternative control path: Use transactional configuration with prechecks, commit confirmation and explicit state verification. The relevant failure for the current situation is: A platform-specific defect can affect the entire fleet before operators can isolate the cause. The distinction follows from: Limited blast radius and observable acceptance criteria avoid a simultaneous fleet-wide regression.

D.

A platform-specific defect can affect the entire fleet before operators can isolate the cause. That is the risk in the reported situation—A provider deploys a new routing template to thousands of devices with uncertain hardware parity. The corrective action is: Roll out a canary group with automated health gates and a tested rollback threshold. Technical basis: Limited blast radius and observable acceptance criteria avoid a simultaneous fleet-wide regression.

Question 241

A network design team is assessing this customer situation: Two WAN access circuits enter the same building duct but are treated as independent failover paths. The customer will accept only measured end-to-end outcomes, not vendor feature claims. Which technical rationale best explains the proposed design choice under these constraints?

  1. Logical carrier labels do not guarantee physical-path independence
  2. Control of L2 fault domains and scalable reachability reduces flooding and unwanted shared fate
  3. Routing adjacencies and management functions need protected CPU budgets separate from bulk forwarding traffic
  4. Stateful middleboxes need bidirectional session context; asymmetric forwarding can cause valid return packets to be dropped

Answer & Explanations

Correct answer: A

A.

Logical carrier labels do not guarantee physical-path independence. This explains the action: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. For the described facts—Two WAN access circuits enter the same building duct but are treated as independent failover paths—test the outcome through: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

B.

The alternative principle is: Control of L2 fault domains and scalable reachability reduces flooding and unwanted shared fate. It instead explains this action: Prefer routed scalable fabric boundaries and explicit overlay segmentation rather than indiscriminate L2 extension. For the present requirement, the controlling mechanism is: Logical carrier labels do not guarantee physical-path independence.

C.

The alternative principle is: Routing adjacencies and management functions need protected CPU budgets separate from bulk forwarding traffic. It instead explains this action: Design control-plane policing and exception capacity from observed legitimate protocol loads. For the present requirement, the controlling mechanism is: Logical carrier labels do not guarantee physical-path independence.

D.

The alternative principle is: Stateful middleboxes need bidirectional session context; asymmetric forwarding can cause valid return packets to be dropped. It instead explains this action: Design route symmetry or approved distributed state sharing around stateful inspection points. For the present requirement, the controlling mechanism is: Logical carrier labels do not guarantee physical-path independence.

Question 242

A network design team is assessing this customer situation: Two WAN access circuits enter the same building duct but are treated as independent failover paths. The customer will accept only measured end-to-end outcomes, not vendor feature claims. Which acceptance result would most convincingly demonstrate that the design addresses the critical requirement?

  1. A constrained-load test preserves essential BGP and routing health while dropping excess punt traffic
  2. A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses
  3. A fault injection measures endpoint reachability, overlay reconvergence and application loss against design limits
  4. A controlled user without administrative identity cannot reach device management, while authorized recovery access works

Answer & Explanations

Correct answer: B

A.

The offered observation would test: Design control-plane policing and exception capacity from observed legitimate protocol loads. It would not establish that the stated requirement has been met. The direct evidence needed here is: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

B.

Direct verification: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses. This is the relevant evidence for the action: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. The reason is: Logical carrier labels do not guarantee physical-path independence.

C.

The offered observation would test: Coordinate overlay tunnel liveness with realistic underlay convergence and failure detection. It would not establish that the stated requirement has been met. The direct evidence needed here is: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

D.

The offered observation would test: Use separately authenticated management paths with restricted reachability and break-glass access. It would not establish that the stated requirement has been met. The direct evidence needed here is: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

Question 243

A network design team is assessing this customer situation: Two WAN access circuits enter the same building duct but are treated as independent failover paths. The customer will accept only measured end-to-end outcomes, not vendor feature claims. Which failure is the most direct risk of taking the tempting design shortcut?

  1. Partially applied network changes can survive despite an apparently successful automation run
  2. Broadcast storms and large failure domains can spread beyond the originating location
  3. A single duct cut can remove both nominally diverse tunnels and isolate the branch
  4. Valid application sessions fail intermittently when traffic returns through a different stateful device

Answer & Explanations

Correct answer: C

A.

The offered consequence belongs to the alternative control path: Use transactional configuration with prechecks, commit confirmation and explicit state verification. The relevant failure for the current situation is: A single duct cut can remove both nominally diverse tunnels and isolate the branch. The distinction follows from: Logical carrier labels do not guarantee physical-path independence.

B.

The offered consequence belongs to the alternative control path: Prefer routed scalable fabric boundaries and explicit overlay segmentation rather than indiscriminate L2 extension. The relevant failure for the current situation is: A single duct cut can remove both nominally diverse tunnels and isolate the branch. The distinction follows from: Logical carrier labels do not guarantee physical-path independence.

C.

A single duct cut can remove both nominally diverse tunnels and isolate the branch. That is the risk in the reported situation—Two WAN access circuits enter the same building duct but are treated as independent failover paths. The corrective action is: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. Technical basis: Logical carrier labels do not guarantee physical-path independence.

D.

The offered consequence belongs to the alternative control path: Design route symmetry or approved distributed state sharing around stateful inspection points. The relevant failure for the current situation is: A single duct cut can remove both nominally diverse tunnels and isolate the branch. The distinction follows from: Logical carrier labels do not guarantee physical-path independence.

Question 244

A network design team is assessing this customer situation: Two WAN access circuits enter the same building duct but are treated as independent failover paths. The customer will accept only measured end-to-end outcomes, not vendor feature claims. Which prerequisite should the architect confirm before choosing and defending this design?

  1. Collect endpoint counts, mobility needs, segmentation requirements and L2 control-plane limits
  2. Document local protocol roles, intent precedence, split-brain safeguards and failure handling
  3. Map forward and reverse routes, state replication capability and routing failure behavior
  4. Obtain last-mile diagrams, provider diversity evidence and dependency mapping

Answer & Explanations

Correct answer: D

A.

The offered preparation belongs with the alternative action: Prefer routed scalable fabric boundaries and explicit overlay segmentation rather than indiscriminate L2 extension. Here the necessary starting condition is: Obtain last-mile diagrams, provider diversity evidence and dependency mapping. It supports: Model physical and provider fate sharing before relying on SD-WAN policy-based failover.

B.

The offered preparation belongs with the alternative action: Separate centralized policy distribution from autonomous local path convergence with explicit authority boundaries. Here the necessary starting condition is: Obtain last-mile diagrams, provider diversity evidence and dependency mapping. It supports: Model physical and provider fate sharing before relying on SD-WAN policy-based failover.

C.

The offered preparation belongs with the alternative action: Design route symmetry or approved distributed state sharing around stateful inspection points. Here the necessary starting condition is: Obtain last-mile diagrams, provider diversity evidence and dependency mapping. It supports: Model physical and provider fate sharing before relying on SD-WAN policy-based failover.

D.

The necessary starting condition is: Obtain last-mile diagrams, provider diversity evidence and dependency mapping. This enables the action: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. Validate the result with: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

Question 245

In a separate customer architecture review, this issue arises: A branch buys circuits from different carriers that share the same last-mile provider. An approved alternate path exists, but its cost and policy limits differ. Which high-level network design choice most directly meets the stated technical and operational requirement?

  1. Model physical and provider fate sharing before relying on SD-WAN policy-based failover
  2. Use transactional configuration with prechecks, commit confirmation and explicit state verification
  3. Design comparable IPv4 and IPv6 path, inspection and segmentation policies end to end
  4. Design control-plane policing and exception capacity from observed legitimate protocol loads

Answer & Explanations

Correct answer: A

A.

Logical carrier labels do not guarantee physical-path independence. For the documented situation—A branch buys circuits from different carriers that share the same last-mile provider—the targeted response is: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. Check: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

B.

The alternative addresses a different technical concern: API acceptance is not the same as converged network behavior; commit and validation semantics vary by platform. The governing mechanism here is: Logical carrier labels do not guarantee physical-path independence. Accordingly, use: Model physical and provider fate sharing before relying on SD-WAN policy-based failover.

C.

Dual-stack endpoints can choose either address family, so protecting only one creates inconsistent behavior. That supports the alternative intervention: Design comparable IPv4 and IPv6 path, inspection and segmentation policies end to end. The present situation—A branch buys circuits from different carriers that share the same last-mile provider—instead calls for: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. Technical basis: Logical carrier labels do not guarantee physical-path independence.

D.

The alternative addresses: Design control-plane policing and exception capacity from observed legitimate protocol loads. Its principle is: Routing adjacencies and management functions need protected CPU budgets separate from bulk forwarding traffic. In this case the needed action is: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. Confirm by: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

Question 246

In a separate customer architecture review, this issue arises: A branch buys circuits from different carriers that share the same last-mile provider. An approved alternate path exists, but its cost and policy limits differ. Which acceptance result would most convincingly demonstrate that the design addresses the critical requirement?

  1. Bidirectional maximum-size application flows succeed with no unexpected fragmentation or PMTU stalls
  2. A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses
  3. A staged change has a confirmed commit, observed operational state and a demonstrated automatic rollback on failure
  4. A controller-loss drill preserves loop-free local failover and reconciles policy cleanly after recovery

Answer & Explanations

Correct answer: B

A.

The offered observation would test: Budget encapsulation overhead and enforce path MTU discovery or appropriate underlay sizing. It would not establish that the stated requirement has been met. The direct evidence needed here is: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

B.

Direct verification: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses. This is the relevant evidence for the action: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. The reason is: Logical carrier labels do not guarantee physical-path independence. The scenario is: A branch buys circuits from different carriers that share the same last-mile provider.

C.

The offered observation would test: Use transactional configuration with prechecks, commit confirmation and explicit state verification. It would not establish that the stated requirement has been met. The direct evidence needed here is: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

D.

The offered observation would test: Separate centralized policy distribution from autonomous local path convergence with explicit authority boundaries. It would not establish that the stated requirement has been met. The direct evidence needed here is: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses.

Question 247

In a separate customer architecture review, this issue arises: A branch buys circuits from different carriers that share the same last-mile provider. An approved alternate path exists, but its cost and policy limits differ. Which failure is the most direct risk of taking the tempting design shortcut?

  1. Fast overlay retries cannot repair missing transport and can amplify churn
  2. Valid application sessions fail intermittently when traffic returns through a different stateful device
  3. A single duct cut can remove both nominally diverse tunnels and isolate the branch
  4. Broadcast storms and large failure domains can spread beyond the originating location

Answer & Explanations

Correct answer: C

A.

The offered consequence belongs to the alternative control path: Coordinate overlay tunnel liveness with realistic underlay convergence and failure detection. The relevant failure for the current situation is: A single duct cut can remove both nominally diverse tunnels and isolate the branch. The distinction follows from: Logical carrier labels do not guarantee physical-path independence.

B.

The offered consequence belongs to the alternative control path: Design route symmetry or approved distributed state sharing around stateful inspection points. The relevant failure for the current situation is: A single duct cut can remove both nominally diverse tunnels and isolate the branch. The distinction follows from: Logical carrier labels do not guarantee physical-path independence. The scenario is: A branch buys circuits from different carriers that share the same last-mile provider.

C.

A single duct cut can remove both nominally diverse tunnels and isolate the branch. That is the risk in the reported situation—A branch buys circuits from different carriers that share the same last-mile provider. The corrective action is: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. Technical basis: Logical carrier labels do not guarantee physical-path independence.

D.

The offered consequence belongs to the alternative control path: Prefer routed scalable fabric boundaries and explicit overlay segmentation rather than indiscriminate L2 extension. The relevant failure for the current situation is: A single duct cut can remove both nominally diverse tunnels and isolate the branch. The distinction follows from: Logical carrier labels do not guarantee physical-path independence. The scenario is: A branch buys circuits from different carriers that share the same last-mile provider.

Question 248

In a separate customer architecture review, this issue arises: A branch buys circuits from different carriers that share the same last-mile provider. An approved alternate path exists, but its cost and policy limits differ. Which prerequisite should the architect confirm before choosing and defending this design?

  1. Catalog YANG and API support, commit behavior, desired-state ownership and rollback hooks
  2. Measure underlay route propagation, overlay keepalive semantics and failure domain
  3. Map forward and reverse routes, state replication capability and routing failure behavior
  4. Obtain last-mile diagrams, provider diversity evidence and dependency mapping

Answer & Explanations

Correct answer: D

A.

The offered preparation belongs with the alternative action: Use transactional configuration with prechecks, commit confirmation and explicit state verification. Here the necessary starting condition is: Obtain last-mile diagrams, provider diversity evidence and dependency mapping. It supports: Model physical and provider fate sharing before relying on SD-WAN policy-based failover.

B.

The offered preparation belongs with the alternative action: Coordinate overlay tunnel liveness with realistic underlay convergence and failure detection. Here the necessary starting condition is: Obtain last-mile diagrams, provider diversity evidence and dependency mapping. It supports: Model physical and provider fate sharing before relying on SD-WAN policy-based failover.

C.

The offered preparation belongs with the alternative action: Design route symmetry or approved distributed state sharing around stateful inspection points. Here the necessary starting condition is: Obtain last-mile diagrams, provider diversity evidence and dependency mapping. It supports: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. The scenario is: A branch buys circuits from different carriers that share the same last-mile provider.

D.

The necessary starting condition is: Obtain last-mile diagrams, provider diversity evidence and dependency mapping. This enables the action: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. Validate the result with: A facility and carrier route audit plus a failure exercise confirms that one event does not sever both accesses. The scenario is: A branch buys circuits from different carriers that share the same last-mile provider.

Question 249

A network design team is assessing this customer situation: A VXLAN overlay fails over slowly because underlay BGP changes lag behind tunnel retries. There is an existing resilience target that the design must not weaken. Which high-level network design choice most directly meets the stated technical and operational requirement?

  1. Coordinate overlay tunnel liveness with realistic underlay convergence and failure detection
  2. Separate centralized policy distribution from autonomous local path convergence with explicit authority boundaries
  3. Model physical and provider fate sharing before relying on SD-WAN policy-based failover
  4. Pin schema versions and test contract compatibility before controller or device upgrades

Answer & Explanations

Correct answer: A

A.

Coordinate overlay tunnel liveness with realistic underlay convergence and failure detection. The relevant technical reason is: Overlay recovery depends on reachability of transport endpoints before higher-layer control can stabilize. Confirm through: A fault injection measures endpoint reachability, overlay reconvergence and application loss against design limits.

B.

Hybrid control allows uniform intent without making all routing liveness depend on controller round trips. That supports the alternative intervention: Separate centralized policy distribution from autonomous local path convergence with explicit authority boundaries. The present situation—A VXLAN overlay fails over slowly because underlay BGP changes lag behind tunnel retries—instead calls for: Coordinate overlay tunnel liveness with realistic underlay convergence and failure detection. Technical basis: Overlay recovery depends on reachability of transport endpoints before higher-layer control can stabilize.

C.

The alternative addresses: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. Its principle is: Logical carrier labels do not guarantee physical-path independence. In this case the needed action is: Coordinate overlay tunnel liveness with realistic underlay convergence and failure detection. Confirm by: A fault injection measures endpoint reachability, overlay reconvergence and application loss against design limits.

D.

The alternative addresses a different technical concern: Model-driven workflows can break when producers and consumers interpret changed data structures differently. The governing mechanism here is: Overlay recovery depends on reachability of transport endpoints before higher-layer control can stabilize. Accordingly, use: Coordinate overlay tunnel liveness with realistic underlay convergence and failure detection.

Question 250

A network design team is assessing this customer situation: A VXLAN overlay fails over slowly because underlay BGP changes lag behind tunnel retries. There is an existing resilience target that the design must not weaken. Which technical rationale best explains the proposed design choice under these constraints?

  1. Logical carrier labels do not guarantee physical-path independence
  2. Overlay recovery depends on reachability of transport endpoints before higher-layer control can stabilize
  3. Stateful middleboxes need bidirectional session context; asymmetric forwarding can cause valid return packets to be dropped
  4. Controller availability without consistent authority can introduce split-brain policy decisions that outlast the partition

Answer & Explanations

Correct answer: B

A.

The alternative principle is: Logical carrier labels do not guarantee physical-path independence. It instead explains this action: Model physical and provider fate sharing before relying on SD-WAN policy-based failover. For the present requirement, the controlling mechanism is: Overlay recovery depends on reachability of transport endpoints before higher-layer control can stabilize.

B.

Overlay recovery depends on reachability of transport endpoints before higher-layer control can stabilize. This explains the action: Coordinate overlay tunnel liveness with realistic underlay convergence and failure detection. For the described facts—A VXLAN overlay fails over slowly because underlay BGP changes lag behind tunnel retries—test the outcome through: A fault injection measures endpoint reachability, overlay reconvergence and application loss against design limits.

C.

The alternative principle is: Stateful middleboxes need bidirectional session context; asymmetric forwarding can cause valid return packets to be dropped. It instead explains this action: Design route symmetry or approved distributed state sharing around stateful inspection points. For the present requirement, the controlling mechanism is: Overlay recovery depends on reachability of transport endpoints before higher-layer control can stabilize.

D.

The alternative principle is: Controller availability without consistent authority can introduce split-brain policy decisions that outlast the partition. It instead explains this action: Use quorum or authority rules and versioned reconciliation to prevent concurrent contradictory intent. For the present requirement, the controlling mechanism is: Overlay recovery depends on reachability of transport endpoints before higher-layer control can stabilize.

Cisco Certified Design Expert (400-007) Practice Tests